Kenmore 625.3485400 Скачать руководство пользователя страница 24

Страница: 24 / 32

SERVICE TECH. INFORMATION

SECTION 5

5B.

ROTARY VALVE SERVICE

Before working on the valve,

turn off the water

supply

and

disconnect from electrical power

TO RELIEVE PRESSURE:

----3 VALVE BYPASS: Close the inlet valve and open

a soft water faucet. Then close the outlet valve and

open the bypass valve.

----SEARS SPECIAL BYPASS: Slide the bypass valve

stem to bypass position.

Loosen

the 3 hex head

screws (see A in drawing) toward the back side of

the valve to allow pressure water to bleed out

Catch water with a rag.

DISASSEMBLY

To remove a part or group of parts, refer to the

valve drawing. A common screwdriver or nut

driver, Phillips screwdriver and pliers are the only

tools needed to completely disassemble.

SERVICING THE VALVE

Inspect all o-rings, seals and gaskets for wear or

defects.

Inspect the bottom surface of the rotor and disc for

scratches, chips or wear.

NOTE: If replacement is needed, be sure to use the

current replacement part.

ASSEMBLY

Be sure all parts are in place and in the proper

position. Lubricate ALL o-rings and seals with FDA

approved silicone grease. To install the rotor seal,

first place the seal into the valve groove, rounded

side down (see cross-section). Apply a light

coating of silicone grease to the seal’s crossing

ribs. Then, carefully center the wear strip on the

seal, and push it downward onto the seal.

Install the nozzle and venturi seal and drain seal.

Assemble 2 o-rings and the wave washer onto the

rotor and disc. Then center the rotor and disc, in

the valve body, on the rotor seal.

Lower the cover onto the valve body and rotor

shaft. Then install the cover holding screws.

Before tightening the screws,

install the valve

cam and gear. Then, turn the rotor (clockwise

only) to service position. Tighten the screws using

a criss-cross pattern. If a torque wrench is

available, torque to 30-40 inch pounds.

Lubricate the gear on the motor, and the valve cam

gear with Molykote grease, or other high quality

gear lubricant.

Be sure to orient switch as shown, with lever

toward the cam.

Содержание 625.3485400

































Результаты поиска

Содержание 625.3485400

Отзывы:

Похожие инструкции для 625.3485400

Бренды по названию

Популярные бренды

Kenmore 625.3485400, Руководство пользователя

Результаты поиска

Содержание 625.3485400

Отзывы:

Похожие инструкции для 625.3485400

Бренды по названию

Популярные бренды