manualshive.com logo in svg

KEMKRAFT KEI-200A, Инструкция пользователя

Поделиться
Скачать
KEMKRAFT KEI-200A Скачать руководство пользователя страница 2

KEMKRAFT

 

ENGINEERING, INC.

 

MODEL KEI-200A SPC DIGITAL INCLINOMETER

 

 

96-014.doc 

 

Page 2 of 8 

47650 CLIPPER DR.  PLYMOUTH TWP.,  MI.  48170  (734) 414-6500 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OPERATION PROCEDURE: 

 

• 

This unit should be calibrated 

once a week minimum

. Refer to the 

Calibration 

Procedure

 of this manual.

 

• 

The Inclinometer should be fully charged before use.  If the unit is used extensively during 
the day it should be charged at night. 

• 

Turn on the power switch, located on the front panel. 

• 

The unit will first display a 2 second Intro Message of  DATE/TIME & Firmware version. 

• 

The unit should display the MAIN MENU as follows: 

 

KEI200-A  0=SETUP

 

1=RUN  2=DOWNLOAD

 

 

• 

Setup should be performed and set to the users parameters before use: 

 

KEI-200A SET UP PROCEDURE 

 
Press 0 -

 From the Main Menu to enter Setup Mode. The unit should display as follows: 

 

SETUP      0=CLOCK 

1=CONFIGURATION

 

 

Press 0

 - To set the DATE and TIME (time is 24 hr mode): 

 

     Press sample key to continue. 

Press 1

 - To setup Configuration for: 

• 

CFG Operator ID:

  The operator will be prompted for an ID number before collecting 

data. 

Содержание KEI-200A









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды