Kellfri 35-FDM160 Скачать руководство пользователя страница 56

Страница: 56 / 56

Kellfri AB

Tel.: +46 511 242 50

In accordance with 2006/42/EC, Appendix 2A
Kellfri AB
Munkatorpsgatan 6
SE-532 40 Skara, Sweden

Hereby declares that the machine
Name: 35-FDM160
Type: Rotary disc mower

Conforms with all applicable requirements in the Machinery Directive 2006/42/EC.
Other equipment must comply with the Machinery Directive's requirements.

WARRANTY TERMS AND CONDITIONS

The warranty's validity

- Kellfri's warranty is valid for 12 months from the date of purchase.

The warranty covers

- Reimbursement for parts replaced after a material fault

or manufacturing fault has been verified.

The warranty
does not cover

- Labour costs
- Travel costs
- Machines on which the purchaser has made or commissioned

modifications.

- Any additional costs arising as a result of damage to the machine.
- Damage due to normal wear and tear of the machine, substandard

servicing, the user's inexperience or use of spare parts that
are not original.

- Wear parts such as hoses, seals, oil and belts.

You are always welcome to give feedback or ask us about our equipment and products.

Kellfri AB has a policy of continuous product development and therefore reserves the right

to make modifications, e.g. to the design and appearance of the product, without prior notice.

CUSTOMER SERVICE

EC DECLARATION OF CONFORMITY FOR MACHINERY, ORIGINAL

Last updated 22/12/2022

Kjell Johansson

Product Development Manager

Содержание 35-FDM160

























































Результаты поиска

Содержание 35-FDM160

Отзывы:

Похожие инструкции для 35-FDM160

Бренды по названию

Популярные бренды

Kellfri 35-FDM160, Руководство пользователя

Результаты поиска

Содержание 35-FDM160

Отзывы:

Похожие инструкции для 35-FDM160

Бренды по названию

Популярные бренды