Kellfri 35-FDM160 Скачать руководство пользователя страница 11

Страница: 11 / 56

Table of Contents >>

All unprotected rotating machine parts increase the risk of accidents. Accidents usually occur when

loose-fitting clothing or long hair is caught and wrapped around rotating parts, such as PTO shafts

or drive shafts on the machine. Ensure that all guards are correctly fitted.

Drive safely on public roads

•

Always follow traffic safety rules on public roads, and following the regulations applying

to driving a tractor with towed equipment on a public road.

•

Check that reflectors, warning signals and/or warning flags indicating protruding equipment

are fitted to the machine or tractor. These indicators must be correctly mounted, and must

be visible and easy for drivers of other vehicles to see.

•

Observers must not lean against or climb onto the machine during transport or during work.

NEVER allow anyone to travel on the machine!

•

The maximum transportation speed must not exceed 20 km/h

•

Brake regulations: If the gross weight of the trailer exceeds the gross weight of the towing

vehicle, the trailer must be equipped with a brake. For further information, contact the traffic

authorities.

•

IMPORTANT! Mark protruding equipment clearly with additional lights or suitable reflectors.

It is important that the equipment is visible! If you are driving on a public road, any load or

equipment protruding in front of or behind the tractor must be marked. In darkness, at dusk

or dawn or in weather with poor visibility, the load must be marked with a white reflector and

lantern at the front and a red reflector and lantern at the rear. In daylight you can mark the

load with a flag or a piece of fabric in colours which are easy to notice, such as red and yellow.

•

Think about front-loaded equipment. As well as marking front-loaded equipment clearly, you

can also try to make front-loaded equipment such as a bucket, bale spike or pallet forks less

aggressive if another driver should collide with it.

•

Before going out onto public roads, it is also always advisable to look over your vehicle and

check that the brake system on the following vehicle is working, and that your tow bar eyes

are not too worn. A worn-out towing eye can break if subjected to a heavy load, and you can

lose the cart.

•

It is also advisable to check that the SMV sign is clearly visible from behind. If it is obscured by

any equipment or load behind, you must hang an additional one at the rear of the vehicle train.

Содержание 35-FDM160

























































Результаты поиска

Содержание 35-FDM160

Отзывы:

Похожие инструкции для 35-FDM160

Бренды по названию

Популярные бренды

Kellfri 35-FDM160, Руководство пользователя

Результаты поиска

Содержание 35-FDM160

Отзывы:

Похожие инструкции для 35-FDM160

Бренды по названию

Популярные бренды