background image

Section 1: Introduction 

Model 3761 10-Channel Low Current Multiplexer Card User's Manual 

 

1-2

3761-900-01 Rev. B

 

/

 

January 2018 

When an interlock is required for safety, a separate circuit should be provided that meets the 

requirements of the application to reliably protect the operator from exposed voltages. The 

digital I/O port of the 3761 is not suitable for control of safety circuits and should not be used 

to control a safety interlock. Bypassing the interlock can result in personal injury or death 

from electric shock. 

System switch / multimeter card compatibility 

The following table lists the cards that are compatible with the 3706 and 3706A. 

Mainframe System Switch / Multimeter 

Compatible plug-in cards 

Model 3706 

3720, 3721, 3722, 3723, 3724, 3730, 3731, 3732, 3740, 

3750 

Model 3706A 

3760, 3761, 3762, 3765 

The 3761 is designed for use only with the Model 3706A System Switch / Multimeter. Using 

the 3761 with the Model 3706 mainframe can cause unpredictable behavior.   

Extended warranty 

Additional years of warranty coverage are available on many products. These valuable contracts 

protect you from unbudgeted service expenses and provide additional years of protection at a fraction 

of the price of a repair. Extended warranties are available on new and existing products. Contact your 

local Keithley Instruments office, sales partner, or distributor for details. 

Series 3700A documentation 

Complete documentation for the Series 3700A System Switch/Multimeter instruments is available at 

the 

Keithley Instruments website

 (

http://www.tek.com/keithley

). The following is a list of available 

documentation. 

Document 

number 

Document name 

Content description 

3700AS-903-01 

Series 3700A System 

Switch/Multimeter Quick Start 

Guide  

Hardware and software requirements, 

switching card installation instructions, 

and a brief description of front-panel 

and remote interface operation  

3700AS-900-01 

Series 3700A System 

Switch/Multimeter User's 

Manual  

Information about scanning, reading, 

writing, and controlling channels  

3700AS-901-01 

Series 3700A System 

Switch/Multimeter Reference 

Manual  

Information about controlling the 

Series 3700A from a remote interface 

Содержание 3761


























Отзывы: