Keiser m3 TBT Скачать руководство пользователя страница 2

Страница: 2 / 16

UNPACKING THE TBT

Carefully remove the TBT from the cardboard box. Lay-out all the components and check to assure

all parts are present and undamaged. If parts are missing or damaged, contact your local dealer,

distributor or Keiser Corporation Service Department. After unpacking and verifying parts, you are

ready to start your assembly. You need an area that is free of dirt, dust or other foreign material that

could impair the assembly of your machine.

BEFORE ASSEMBLING

Always follow the steps in this manual as you assemble your M3 TBT. Do not skip, substitute or modify

any steps or procedures of this assembly, as doing so could result in personal injury and will void your

warranty. We have put a number of precautions in this manual.

PARTS INVENTORY

- Left Handle (550832S/X)

- Pedal Set (555438)

Right Handle (550833S/X)

- Flywheel Guard & Cap (553101B/X & 555073)

- Base Frame (550814G/X)

- M Series Computer

- TBT Main Frame (550826PBC/XXC)

- Foot Rests (550834)

- Flywheel (555003)

- M Series Computer

- Hubcap (555005)

NOTE:

Informs you about things we recommend you do or are aware of, before

performing the assembly. These notes are placed in the manual to aid you during a

certain procedure or to make you aware of any general mandatory actions or information.

WARNING:

This symbol appearing throughout this manual means

PAY ATTENTION! BE

ALERT!

When you see this warning symbol, your safety is involved. It is being used to

call attention to POTENTIAL hazards that could result in personal injury or loss of life.

Содержание m3 TBT

















Результаты поиска

Содержание m3 TBT

Отзывы:

Бренды по названию

Популярные бренды

Keiser m3 TBT, Руководство пользователя

Результаты поиска

Содержание m3 TBT

Отзывы:

Бренды по названию

Популярные бренды