manualshive.com logo in svg

Kees van der Westen Slim Jim mirage, Руководство пользователя

Поделиться
Скачать
Kees van der Westen Slim Jim mirage Скачать руководство пользователя страница 15

USER MANUAL - operation 

Slim Jim User manual 

 

page 14 

Use external temperature sensor (option) 

An external NTC-sensor can be plugged into the bottom of the electrics tray (see Figure 21, page 28). 
The temperature of the external sensor can be shown on the control panel instead of the steam boiler 
temperature. 

In the menu window touch the button “EXTERNAL SENSOR”. 

menu window

 

 

 

 

 

touch 

 

 

 

 

 

 

 

 

 

 

 

external sensor 
window Triplette

 

 

external sensor 

attached (°C)

 

 

 

 

 

 

 

 

external sensor 
window Duette

 

 

external sensor 

attached (°F)

 

 

 

 

 

 

touch 

 

 

 

 

 

 

 

 

 

return to operational window

 

 

 
There is a filter-basket with NTC sensor available that will register the temperature in the coffee-bed 
during extraction and can be helpful to check functioning of the different groups. Of course you can 
also check the mix-water temperature with this item. 
 

 

Figure 12. Temperature sensor in filter basket (mounted in bottomless portafilter). 

 
Although the input of the “external sensor” is displayed without delay, the temperature shown will 
always be lagging a bit w.r.t. the actual temperature at the sensor-tip as the probe-temperature needs 
to adjust to the surrounding temperature. Response time of this sensor to 90% (of the temperature 
difference) is appr. 1 second. 
 

 

STAND

BY

EXTERNAL

SENSOR

CLEAN

PROGRAM

SETTINGS

13 : 57

GROUP 1

93.4

GROUP 2

45.6

GROUP 3

93.2

EXTERNAL

80.4

EXIT

GROUP 1

200.1

GROUP 2

114.1

EXTERNAL

176.7

EXIT

Содержание Slim Jim mirage


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды