manualshive.com logo in svg

Kees van der Westen Slim Jim mirage, Руководство пользователя

Поделиться
Скачать
Kees van der Westen Slim Jim mirage Скачать руководство пользователя страница 13

USER MANUAL - operation 

Slim Jim User manual 

 

page 12 

Sensor malfunction 

For each boiler sensor, the corresponding area in the display, as well as the 3-digit display, will show 
O.C. (open circuit, infinite resistance)  or C.C. (closed circuit, electric short) if there is a sensor 
malfunction. When a sensor malfunction is shown for a boiler, the heating of that boiler is dis-engaged. 
The machine will remain functional on the other boilers. When there is a steam boiler sensor 
malfunction the indicator LED(s) on the Bastone units or touchpads will flash continuously. 

Even though the coffee boilers will remain operational when there is a steam boiler sensor error, 
overall functionality of the machine will be low. When the display shows a boiler-sensor malfunction, 
have the machine repaired as soon as possible (probably the sensor has to be replaced).  

operational window

 

 

an open circuit is 

detected at group 1 

temperature sensor

 

 

As the sensor in the distribution block has no designated area on the control panel, a sensor error is 
indicated by a red centre line in all groups. There is no distinction between open or closed circuit. With 
a malfunctioning sensor, the cool-valve will not open but the machine will remain functional. A non-
functional cool valve may lead to overheating of the groups and rapid decay of the flow-meters in the 
machine. Have the machine repaired as soon as possible. 

operational window

 

 

a distribution block 

sensor malfunction 

is detected

 

 

Technical assistance 

In the no-heat or eco window (shown below) touch the left of the control panel. The next window will 
show the telephone number to call for technical assistance, provided that the technician has entered 
the information. The exit button 

will return to “NO HEAT” or “ECO MODE”, whatever the earlier setting 

was. 

no-heat window

 

 

“NO HEAT”: the 

machine will cool 

down

 

 

 

 

 

 

 

 

eco window

 

 

“ECO”: the machine 

will settle at lower 

set temperature

 

 

touch 

 

 

 

 

 

 

 

 

 

 

assistance window

 

 

 

 

 

 

 

 

touch 

 

 

 

 

 

 

 

 

 

EXIT will go back to previously active window 

 (NO HEAT or ECO)

 

 

 

 

GROUP 1

O.C.

GROUP 2

45.6

GROUP 3

93.2

STEAM

124.6

MENU

GROUP 1

93.4

GROUP 2

45.6

GROUP 3

93.2

STEAM

124.6

MENU

THURSDAY            13 : 57

TECH. ASSISTANCE

KEES VAN DER WESTEN

SLIM JIM

NO HEAT

THURSDAY  

13 : 57

TECH. ASSISTANCE

KEES VAN DER WESTEN

SLIM JIM

ECO

TELEPHONE NUMBER FOR TECHNICAL ASSISTANCE

+31 6 12345678

EXIT

Содержание Slim Jim mirage


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды