Keeler Cryomatic MKII Скачать руководство пользователя страница 9

Страница: 9 / 33

Home

Back

4. Safety

Caution
• Use only genuine Keeler approved parts and accessories or
device safety and performance may be compromised

• The product has been designed to function safely when at an
ambient temperature b10°C and +35°C

• Keep out of the reach of children

• To prevent condensation from forming, allow instrument to
come to room temperature before use

• For indoor use only (protect from moisture)

• Keep the console away from sources of liquids and do not
spray with water

• This product is suitable for use with only Nitrous Oxide or
Carbon Dioxide medical gases

• Only non-syphonic gas cylinders should be used with this device

• No modification of this equipment is allowed

• Care should be taken not to trap fingers in pinch points

during gas bottle change

• Follow guidance on cleaning / routine maintenance to
prevent personal injury / damage to equipment

Switch off the electrical supply and disconnect from the

mains electrical supply before cleaning and inspection

• Do not use hypercarbonate or phenolic based cleaning

solutions or disinfectants containing cationic surfactants (e.g.
Dettox) to clean the console

•  Failure to carry out recommended routine maintenance as per
  these Instructions for Use may reduce the operational lifetime
  of the product

• There are no user serviceable parts inside. Contact authorised
service representative for further information

• At product end of life dispose of in accordance with local
environmental guidelines (WEEE)

• In the unlikely event that the probe fails to defrost, immediately
switch off the console and apply saline solution to the probe

• Do not obstruct the vent holes on the disposable probe (located
on the tube) and reusable probe, located as indicated below

Содержание Cryomatic MKII


































Результаты поиска

Содержание Cryomatic MKII

Отзывы:

Похожие инструкции для Cryomatic MKII

Бренды по названию

Популярные бренды

Keeler Cryomatic MKII, Инструкция по эксплуатации

Результаты поиска

Содержание Cryomatic MKII

Отзывы:

Похожие инструкции для Cryomatic MKII

Бренды по названию

Популярные бренды