Keeler Cryomatic MKII Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 33

background image

Next

Home

Back

4

2. Introduction

Thank you for purchasing your Keeler Cryomatic MKII.

We have taken the greatest care in the design, development and
manufacture of this product to ensure that you get many years of
trouble free service. However, it is important that you read the
descriptions, installation and operating instructions carefully prior
to installing or using your new Cryomatic MKII.

About this Manual

This handbook forms the Instructions for Use for the Keeler
Cryomatic MKII, a clinical instrument for cryogenic ophthalmic
surgery.

It contains complete, step-by-step instructions for the
Cryomatic MKII and is intended for use by trained medical
personnel. This manual does not contain clinical instructions or
any recommendations for medical applications. The use of the
Cryomatic MKII in any surgical procedure must always be at the
discretion of a licensed medical practitioner.

Intended use

The Keeler Cryomatic MKII System and probes are for use in
ophthalmic surgery such as cryopexy for retinal detachment, cyclo
destructive procedures in refractory glaucoma, extraction of
fragments within the vitreous cavity, cataract extraction, cryo
destruction of lash follicles for trichiasis and treatment of
retinopathy of prematurity (ROP).

Once the Cryo probe has been correctly positioned the freeze
control is activated and an ice ball is formed around the tip of the
Cryo probe and the adjacent area.

Please read and follow these instructions carefully.

«
...
2
3
4
5
6
...
»

Содержание Cryomatic MKII


































Отзывы:

Нет отзывов

Похожие инструкции для Cryomatic MKII

Бренд: Baker Instrument Company Страницы: 24

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Makita Страницы: 8

Бренд: VECTECH Страницы: 5

Бренд: Velocitek Страницы: 81

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: Ognibene Страницы: 28

Бренд: Hameg Страницы: 24

Бренд: Vaisala Страницы: 118

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Бренд: Teac Страницы: 76

Бренд: Teac Страницы: 3

Бренд: Teac Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды