background image

GB - 10

Control circuit

2.1.2  IO-link device interface

X4B

PIN

Name

Function

1

L+

Voltage input 

18…30 Vdc  /  500 mA

2

C/Q

Transmission signal

Input: 18…30 Vdc Ri:10…40 kΩ

Output: 18…30 Vdc I: 220…480 mA

3

L-

0V

Baud rate: 38.4 kBd

Accuracy of the transmission speed: ±0.16 %

Bus and control card supply voltage are not isolated.

Assembly of connecting wires with wire-end ferrules 

according to DIN46228/4

Assembly of connecting wires 

without wire-end ferrules

Cross-section / AWG

Metal sleeve length

Stripping length

Cross-section / AWG

Stripping length

0.2…0.75 mm

2

 / 24…19

6 mm

8 mm

0.2…1.5 mm

/ 24…16

10 mm

Connecting wires rigidy and flexible

2.1.3  Assembly of the wires

Required tools:

Screw driver SD 0.4 x 2.5 (DIN 5264)

1. Strip cable

Use wire-end ferrules as round, square or hexagon 

pressing.

2. Plug screw driver mid into the square slot.

3. Plug cable into the round slot, that no wires can be seen 

from the outside.

4.

Remove screw driver and check if cables are fixed.

A safe clamping can not be guaranteed when using shorter wire-end ferrules. 

KEB generally recommends the use of wire-end ferrules in industrial environments.

Содержание COMBIVERT G6

























Отзывы: