KBR multicomp F144-MS-1V1C1TI6DO6RO-3 Скачать руководство пользователя страница 16

Страница: 16 / 68

Rev. 1.00

22586_EDEBD

A0253-0318-1_EN

KBR multicomp F144-3 6DO/6RO

Installation and electrical connection

Installation and electrical connection of

the system

4.1

General, very important information



Tighten all screws and connections. Failure to do so will void the warranty.



Install and operate the device in accordance with the applicable VDE regula-

tions (in particular VDE 0100) and the electricity supplier's regulations.



Connection cross-sections and fuse protection table: see annex.

CAUTION!

Failure to observe the connection conditions or exceeding the permissible
voltage range may result in damage or destruction of the device.

Before connecting the power supply to the device, please note:



The voltage and frequency must comply with the specifi cations on the name-

plate. Observe the limits specifi ed in this manual!



The electrical installation of the building must have a circuit-breaker or fuse

for the power supply voltage, in accordance with the applicable local regula-
tions.



Install an isolating switch that is easily accessible to the user and close to the

device. It must be marked as an isolating switch for this device.



Install a suitable, correspondingly marked fuse and isolating switch for the

voltage measurement inputs nearby (or, alternatively, a circuit breaker). These
voltages are hazardous live!



Voltages that exceed the permissible rated voltages must be connected via a

voltage transformer.



Measuring voltages and measuring currents must come from the same net-

work.

Содержание multicomp F144-MS-1V1C1TI6DO6RO-3





































































Результаты поиска

Содержание multicomp F144-MS-1V1C1TI6DO6RO-3

Отзывы:

Похожие инструкции для multicomp F144-MS-1V1C1TI6DO6RO-3

Бренды по названию

Популярные бренды

KBR multicomp F144-MS-1V1C1TI6DO6RO-3, Справочник

Результаты поиска

Содержание multicomp F144-MS-1V1C1TI6DO6RO-3

Отзывы:

Похожие инструкции для multicomp F144-MS-1V1C1TI6DO6RO-3

Бренды по названию

Популярные бренды