background image

X – LIMITED WARRANTY

For a period of 18 months from date of original purchase, KB will repair or replace without
charge devices which our examination proves to be defective in material or workmanship.
This warranty is valid if the unit has not been tampered with by unauthorized persons,
misused, abused, or improperly installed and has been used in accordance with the
instructions and/or ratings supplied.  The foregoing is in lieu of any other warranty or
guarantee, expressed or implied, and we are not responsible for any expense, including
installation and removal, inconvenience, or consequential damage, including injury to any
person, caused by items of our manufacture or sale.  Some states do not allow certain
exclusions or limitations found in this warranty so that they may not apply to you.  In any
event, KB's total liability, under all circumstances, shall not exceed the full purchase price
of this unit.  (rev 4/88)

KB ELECTRONICS, INC.

12095 NW 39th Street, Coral Springs, FL  33065 • (954) 346-4900 • Fax (954) 346-3377

Outside Florida Call 

TOLL FREE

 (800) 221-6570 • 

E-mail

 – [email protected]

www.kbelectronics.com

(A40400) – Rev. B – 3/98

Содержание KBPC-240D








































Отзывы: