background image

KBAC SERIES INSTALLATION AND OPERATION MANUAL 

23

13 – DIAGNOSTIC LEDs 

The drive contains two diagnostic LEDs mounted on the enclosure cover to display the drive's operational status. 

 

 

WARNING!

 Do not depend on the PWR LED as a guaranteed power off condition. Be sure the main power switch or circuit breaker is in 

the "OFF" position before servicing this drive. 
 

13.1 – POWER ON LED (PWR) 

The "PWR" LED will illuminate green when the AC Line is applied to the drive. 
 
 

13.2 – STATUS LED (ST) 

The "ST LED is a tricolor LED which provides 
indication of a fault or abnormal condition. The 
information provided can be used to diagnose 
an installation problem such as incorrect input 
voltage, overload condition, and drive output 
miswiring. It also provides a signal which 
informs the user that all drive and 
microcontroller operating parameters are 
normal. Table 6 summarizes the "ST" LED 
functions. 
 
 
 
 
 
 
 
 
 
 
 
 
 

14 – OPTIONAL ACCESSORIES 

Detailed instructions are provided with all accessories. See Table 7. 
 

TABLE 7 

OPTIONAL ACCESSORIES 

Description KBAC-24D KBAC-27D KBAC-29 KBAC-29 

(1P) KBAC-45 

KBAC-48 

KBAC-217 Series
KBAC-416 Series

Forward-Stop-Reverse Switch Kit:

 Provides 

motor reversing and stop functions. Mounts on the 
enclosure cover and is supplied with a switch seal 
to maintain liquidtight integrity. 

9480 9480 

9480 9480 9480 

9480  8888 

On/Off AC Line Switch Kit:

 Disconnects the AC 

Line. Mounts on the enclosure cover and is 
supplied with a switch seal to maintain liquidtight 
integrity. 

9482 9523 

9523 9523 9532 

9532 

"S" Suffix Models

(Factory Installed)

Run-Stop-Jog Switch Kit:

 Selects speed setting 

from either the Main Speed Potentiometer or the 
JOG Trimpot. Mounts on the enclosure cover and 
is supplied with a switch seal to maintain liquidtight 
integrity. 

9340 9340 

9340 9340 9340 

9340  8889 

SIAC-PS Signal Isolator Kit:

  Provides 

isolation between a non-isolated signal 
source and the drive. Mounts on the drive’s 
PC board with four snap-ins. 

2G 

9600C 9600C 

9600C 9600C 9600C 

9600C 

— 

3G

1

 

8890 8890 

8890 8890 8890 

8890  8890 

Auto/Manual Switch Kit:

 When used with the 

Signal Isolator, it selects remote process signal or 
the Main Speed Potentiometer. Mounts on the 
enclosure cover and is supplied with a switch seal 
to maintain liquidtight integrity. 

9481 9481 

9481 9481 9481 

9481  8891 

SIAC-PS Signal Isolator Kit and Auto/Manual 
Switch Kit

 

9605 9605 

9605 9605 9605 

9605  8893 

AC Line Filter Kit

2

:

 Provides Class A RFI 

(EMI) suppression. Installs onto the drive’s 
PC board with quick-connect terminals. 
"S" Suffix filter is used when On/Off AC Line 
Switch is installed. "NS" Suffix filter is used 
when On/Off AC Line Switch is not installed. 

"S" 

Suffix 

9507 

9512 

9479 — 9479 

9479 

"F" Suffix Models

(Factory Installed)

"NS" 

Suffix 

9507 

9512 

9515 — 9515 

9515 

Liquidtight Fittings Kit: 

Provide a liquidtight seal 

for wiring the drive. 

9526 9526 

9526 9526 9526 

9526  8892 

Notes: 1.

 Third Generation (3G) drives are marked "(3G)" on the product label. 

2.

 Complies with CE Council Directive 89/336/EEC Industrial 

Standard.

TABLE 6 

DRIVE OPERATING CONDITION AND STATUS LED INDICATOR

Drive Operating Condition

Flash Rate

1

 and LED Color

Normal Operation

Slow Flash Green

Overload (120% – 160% Full Load)

Steady Red

2

I

2

t (Drive Timed Out)

Quick Flash Red

2

Short Circuit

Slow Flash Red

Undervoltage

Quick Flash Red / Yellow

3

Overvoltage

Slow Flash Red / Yellow

3

Stop

Steady Yellow

Stand-By

4

Slow Flash Yellow

Input Phase Loss

5

Rapid Flash Yellow

Overtemperature Trip

6

Slow / Quick Flash Red

1

Notes: 1.

 Slow Flash = 1 second on and 1 second off. Quick Flash = 0.25 second on and 

0.25 second off. 

2.

 When the Overload is removed, before the I

2

t times out and trips the 

drive, the "ST" LED will flash green. 

3.

 When the Undervoltage or Overvoltage condition is 

corrected, the "ST" LED will flash Red / Yellow / Green. 

4.

 Only if the Forward-Stop-Reverse 

Switch is installed. 

5.

 KBAC-29, with three-Phase AC Line input and KBAC-45, 48. 

Rapid Flash = 4 mSec on and 6 mSec off. 

6.

 KBAC-217, 416 Series only. 

Содержание KBAC-24D

























Отзывы: