– 17 –
〔4〕CHECK AND ADJUST MODES
※ This section describes the modes needed for performing checking and adjustments when a problem occurs.
※ Before running these modes, you need to switch to the Silent Mode by pulling the mute lever located
under the keybed (at the treble side).
【A】Activating the Check Mode
Starting.from.power-off,
Press down and hold the [Value ▼ ], [Tone] and [Dual] buttons simultaneously, then turn the power on.
When the following menu message appears on the LCD, release the buttons.
ＫＰ９５０Ｂ ＡＴＸｓＧｊ
＝＝ Ｃｈｅｃｋ Ｍｏｄｅ ＝＝
turns after a moment into
１．ＳＷ ＆ ＬＥＤ
.
※ To exit from the Check Mode, turn the power off.
【B】Checking Switches and Pedal Sensors
① Press all switches buttons in rotation and check if the corresponding switch name appears on the
LCD display.
[Play/Stop]
１．ＳＷ ＆ ＬＥＤ
１ ＶＡＬＵＥ ＵＰ
[Value ▼ ]
１．ＳＷ ＆ ＬＥＤ
６ ＶＡＬＵＥ ＤＯＷＮ
[Rec]
１．ＳＷ ＆ ＬＥＤ
２ ＰＬＡＹ＿ＳＴＯＰ
[Tone]
１．ＳＷ ＆ ＬＥＤ
7 ＴＯＮＥ
[Demo]
１．ＳＷ ＆ ＬＥＤ
３ ＲＥＣ
[Dual]
１．ＳＷ ＆ ＬＥＤ
８ ＤＵＡＬ
[Menu]
１．ＳＷ ＆ ＬＥＤ
４ ＤＥＭＯ
[Reverb]
１．ＳＷ ＆ ＬＥＤ
９ ＲＥＶＥＲＢ
１．ＳＷ ＆ ＬＥＤ
５ ＭＥＮＵ
[Metronome]
１．ＳＷ ＆ ＬＥＤ
５ ＭＥＴＲＯＮＯＭＥ
② Make sure that the LED light is turning on and off when pressing the switch buttons, except for
“Value”.
※ If nothing appears on the LCD or the LED does not turn on and off when the switch button is
depressed, the circuit board inside the switch panel may be defective.
③ Press down each pedal, and check if the following message appears on the LCD for each pedal.
Soft
１．ＳＷ ＆ ＬＥＤ
Ｓｏｆｔ Ｐｅｄａｌ
Sostenuto
１．ＳＷ ＆ ＬＥＤ
Ｓｏｓｔｅｎｕｔｏ Ｐｅｄａｌ
Damper
１．ＳＷ ＆ ＬＥＤ
Ｄａｍｐｅｒ ＸＸＸ
ＸＸＸ
：Check if the value varies from 0 to 127 when the damper pedal is being depressed deeply.
(The actual degree value is eight steps but not 128 steps.)
If.the.Soft.or.Sostenuto.pedal.has.a.problem
③ Adjust the switch position according to 【E】 “Adjusting the Pedal Sensor”.
※ If the message does not appear on the LCD even after adjusting all the Soft, Sostenuto and Damper
switches, check cable and connector of each switch.
【C】Checking the LCD
Starting.from.the.Check.Mode.of.the.switch,
press the [Reverb] and [Metronome] buttons simultaneously.
ＫＰ９５０Ｂ ＡＴＸｓＧｊ
＝＝ Ｃｈｅｃｋ Ｍｏｄｅ ＝＝
When the message above is displayed, press the [Demo] or [Menu] button.
■■■■■■■■■■■■■■■■
■■■■■■■■■■■■■■■■
When the [Demo] button is pressed.
When the [Menu] button is pressed
If dots are missing when the [Menu] button is pressed, the LCD is faulty.
※ Press again the [Reverb] and [Metronome] buttons simultaneously to return to the Check Mode of
the switch.
１．ＳＷ ＆ ＬＥＤ
