Kasei KZ-5121CS страница 5 Скачать руководство пользователя

Страница: 5 / 46

EXPLANATION OF SYMBOLS AND SAFETY

WARNINGS

(1)

Read owner

＇

s manual before operating this machine.

(2)

Wear head, eye and ear protection.

(3)

Warning! Kickback is danger.

(4)

Warning/Attention .

IMPORTANT

If warning seals peel off or become soiled and impossible to read ,you

should contact the dealer from which you purchased the product to order new
seals and affix the new seal(s)in the required location(s).

EXPLANATION OF SYMBOLS AND SAFETY

WARNINGS

(1)

Read owner

＇

s manual before operating this machine.

(2)

Wear head, eye and ear protection.

(3)

Warning! Kickback is danger.

(4)

Warning/Attention .

IMPORTANT

If warning seals peel off or become soiled and impossible to read ,you

should contact the dealer from which you purchased the product to order new
seals and affix the new seal(s)in the required location(s).

Содержание KZ-5121CS















































Результаты поиска

Содержание KZ-5121CS

Отзывы:

Похожие инструкции для KZ-5121CS

Бренды по названию

Популярные бренды

Kasei KZ-5121CS, Руководство оператора

Результаты поиска

Содержание KZ-5121CS

Отзывы:

Похожие инструкции для KZ-5121CS

Бренды по названию

Популярные бренды