background image

18

 

15 

container. 

NOTE 

Most engine troubles are caused ,directly or indirectly, by 

the fuel used on the machine .Take special care not to mix 

a motor oil for 4 cycle engines. 

    

  CHAIN OIL

 

Use motor oil SAE

30-

40 in summer and SAE

20 in winter. 

NOTE 

Do not use wasted or regenerated oil that can cause damage 

to the oil pump. 

 

FUELING 

 

Never refuel the machine while the engine is running. 

 

Make sure there is plenty of ventilation when refuelling or mixing 

fuel (gasoline and 2-stroke oil). 

 

Move the machine at least 3m from the refuelling point before 

starting it. 

 

If you have spilled fuel or chain oil on the machine. Wipe off the 

spillage and allow remaining fuel to evaporate 

 

If the machine is leaking fuel. Check regularly for leaks from the 

fuel cap and fuel lines. 

 

1.

 

Unwist and remove fuel cap. Rest the cap on a dustless palce. 

2.

 

Put fuel into the tank to 95% of the full capacity. 

3.

 

Fasten the fuel cap securely and wipe up any fuel spillage around 
the unit. 

 

CHECKING OIL SUPPLY 

Check the chain lubrication each time you refuel.After starting 

the engine,run the chain at medium speed and see if chain oil is 

scattered off as shown in the figure. 

Содержание KZ-5121CS















































Отзывы: