manualshive.com logo in svg
background image

13 

 

 

 

 

 

 

 

 

 

Warranty 

 

Warranty Policy 

Warranty period:   

2400VFX, 3400(H)VFX, 4400(H)VFX = 2-year Limited Warranty 

8400VFX, 2.3(H)VFX, 5.1VFX, 5.3(H)VFX = 3-year Limited Warranty 

Kasco® Marine, Inc. warrants this aerator to be free from defects in material or workmanship under normal use and service 
(excluding ropes, power cord, and propeller). The Kasco Marine, Inc. obligation under this warranty is limited to replacing or 
repairing free of charge any defective part within the warranty period from the date of shipment. Customer shall pay shipping 
charges for returning the unit to Kasco or an Authorized Repair Center. 

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND ANY OTHER OBLIGATION OR 
LIABILITY WHATEVER ON THE PART OF KASCO MARINE, INC. AND IN NO EVENT SHALL KASCO MARINE, INC. BE LIABLE 
FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES. 

Warranty is void if:  

 

The aerator 

is not maintained properly according to the Maintenance Recommendations supplied in this Owner’s Manual.

 

 

The aerator is returned for repair without the power cord 

 

The unit, control panel, or power cord are altered in any way from original shipment.  

Cuts in the power cord are not 

covered under warranty.

 

 

The aerator is damaged by unauthorized tampering. 

 

The sacrificial zinc anode around the propeller shaft shows significant deterioration (not maintained according to 

Reco

mmendations supplied in this Owner’s Manual

 

Warranty Claim Procedure:

 The best method for establishing warranty period is by keeping your original receipt and registering 

the equipment online at kascomarine.com under the Warranty Information section.  

Once warranty coverage has been established, the unit may be sent to Kasco Marine or any Kasco Authorized Repair Center for 
evaluation and repair. See 

Repair

 section on the next page for more information regarding warranty repair procedure. 

Содержание VFX Series




















Отзывы: