manualshive.com logo in svg
background image

2

 

Important Safety Instructions. . . .  

pg2 

General Owner’s Instructions. . . . 

 

pg2 

Unit Specs. . . .  

pg4 

VX Pattern Sizes. . . .  

pg4 

2400VFX, 3400(H)VFX, 4400(H)VFX Parts Included. . . .  

pg5 

2400VFX, 3400(H)VFX, 4400(H)VFX Assembly. . . .  

pg6 

VFX Installation Instructions. . . .  

  pg8 

Control Panel Installation. . . .  

  pg9 

C-25 Timer Control Instructions. . . .  

pg10 

C85 / C95 non-metallic Control Panel Timer. . . .  

pg11 

2400, 3400, 4400 Parts Diagram. . . .  

pg12 

Maintenance Recommendations. . . .  

pg13 

Warranty Policy. . . .  

pg14 

Troubleshooting Tips. . . .  

pg15 

Customer Repair Form. . . .  

pg17 

Registration Information. . . .  

pg18 

 

 

THANKS 

We at Kasco Marine, Inc. would like to both thank and congratulate you on your purchase of the VFX model aerator.  We appreciate 

you choosing Kasco and for your purchase.  Your decision to purchase Kasco’s VFX model Aerator will not disappoint you.  The 

VFX 

model Aerator will be a great addition to your body of water.  It will help improve the water quality by adding much needed oxygen and 
circulation.  It will also enhance the aesthetics of the pond or lake with a beautiful pattern.  The lighting package (if purchased) will 
illuminate your aerator for beauty at night.  We thank you for choosing Kasco for your aerator needs and want you to be completely 
satisfied with your purchase. 

Important Safety Instructions 

Please read and follow these extremely important safety and handling instructions for your Kasco equipment.  Following these 

instructions will help ensure your safety and the quality performance of your equipment.

 

 

Under NO circumstances should anyone enter the water with the electrical equipment plugged in and/ or in operation. Kasco 
equipment is ETL approved to UL and CSA standards for safety in water.  However, it is NEVER recommended to enter the water 
with the equipment in operation. 

 

Caution should be used when dealing with any electrical equipment with moving parts. 

 

NEVER run the unit out of water.  It will damage the seals and create a dangerous situation for the operator. 

 

Extreme caution should be used around water, especially cold water, such as in Spring, Fall, and Winter, which poses a hazard in 
and of itself. 

 

NEVER lift or drag the aerator by the power or light cord.  If you need to pull the unit to the side of the pond, use the anchoring 
ropes. 

 

Do not use waders in deep ponds/lakes or ponds/lakes with drop-offs, drastic slopes, or soft bottom material. 

 

Do not use boats that tip easily for aerator installation, such as a canoe, and follow all boating safety rules and regulations, including 
wearing a PFD. (Personal Flotation Device) 

Содержание 2400VFX



















Отзывы: