manualshive.com logo in svg
background image

1/2HP-1HP AERATOR & CIRCULATOR  MANUAL

17

Warranty Period: Models 2400A/C, 3400A/C, 

3400HA/HC, 4400A/C, 4400HA/HC = 2 years 

Kasco® Marine, Inc. warrants this aerator/circulator 

to be free from defects in material or workmanship 

(except for the ropes, power cord, and propeller) un-

der normal use and service. The Kasco Marine, Inc. 

obligation under this warranty is limited to replacing 

or repairing free of charge any defective part within 

the warranty period. Customer shall pay shipping 

charges for returning the unit to Kasco or an Autho-

rized Repair Center. 

THIS WARRANTY IS IN LIEU OF ANY OTHER WAR-

RANTIES, EXPRESSED OR IMPLIED, AND ANY OTHER 

OBLIGATION OR LIABILITY WHATEVER ON THE PART 

OF KASCO MARINE, INC. AND IN NO EVENT SHALL 

KASCO MARINE, INC. BE LIABLE FOR ANY SPECIAL OR 

CONSEQUENTIAL DAMAGES. 

Warranty is void if: 

• 

The unit is not maintained properly according to 

the Maintenance Recommendations supplied in 

this manual. 

• 

The unit is returned for repair without the power 

cord or if the unit, control box, or power cord 

are altered in any way from original shipment. 

Cuts in the power cord are not covered under 

warranty. 

• 

The unit is damaged by unauthorized tampering. 

• 

The sacrificial anode around the propeller shaft 

shows significant deterioration. (The anode must 

be inspected periodically and replaced if neces-

sary.) 

Warranty Claim Procedure: The best method for es-

tablishing warranty period is via the original receipt. 

Also, register the unit online at: www.kascomarine.

com. Once the warranty coverage has been estab-

lished, the unit may be sent to any Kasco Authorized 

Repair Center for evaluation and repair. Please call 

Kasco Marine at 715-262-4488 prior to shipping to 

receive any updated information and/or repair form 

or call Kasco Marine at 715-262-4488 to locate your 

nearest Authorized Repair Center. You can also 

email Kasco at [email protected]

Please include the repair form received from Kasco 

Marine or your local distributor with the shipment. 

If no repair form is available, include your name and 

physical address for return delivery of the repaired 

unit and a daytime phone number and/or e-mail 

address for correspondence regarding the warranty 

claim. Any expedited shipping method for the return 

of the unit is at the customer’s expense. Kasco Ma-

rine will return units repaired under warranty at our 

expense via ground freight within the continental 

United States. 

Other Repairs

Most failed equipment can be repaired at substan-

tially lower costs than replacement with new. Please 

ship according to the instructions in the previous 

section. 

Kasco Marine does estimates on repairs at the re-

quest of the customer. The request for an estimate 

should be included in the letter that accompanies 

the returned unit and must include a daytime phone 

number and/or e-mail address. Estimate options are 

as follows: 

• 

We will contact the customer with a total esti-

mated cost for repairs after we have evaluated 

the unit but before we perform the work. 

• 

We will repair the unit only if repair costs are 

under a dollar amount stated by the customer. 

Example: “Please repair if total is under $150.00 

before shipping charges.” 

All estimates that are rejected for repair will be de-

stroyed unless otherwise directed by the customer. 

If the customer would like the unit returned, the unit 

will be restored as closely as possible to the condi-

tion in which it was received and shipped at the cus-

tomer’s expense for shipping and handling charges. 

Billing: Kasco Marine also accepts Visa and Master-

Card credit card payments. Kasco Marine will call 

for credit card information upon completion of the 

estimate at the customer’s request. All other warran-

ty and repair inquiries should be directed to Kasco 

Marine, Inc. at 715-262-4488 or repairs@kascomar-

ine.com 

WARRANTY

Back to Contents

Содержание 2400





















Отзывы: