Kärcher SC 5 EasyFix Premium, Инструкция по эксплуатации

Страница: 14 / 202

14 English
Regulating the steam volume
The expelled steam volume is regulated using the se-
lector switch for steam volume. The selector switch has
the setting options min. steam stage for light soiling to
max. steam stage for heavy soiling. The VapoHydro
function is for the removal of heavy soiling in areas that
are difficult to access.
1. Set the selector switch for the steam volume to re-
quired steam volume.
2. Press the steam lever.
3. Before starting cleaning, point the steam gun at a
cloth until steam is expelled evenly.
Refilling water
If there is not enough water, the water shortage indicator
lamp flashes red and a signal tone sounds.
Note
The water pump fills the steam boiler at intervals. If the
filling is successful, the red water shortage indicator
lamp goes out.
Note
If there is no or too little water in the steam boiler, the
water pump starts to run and pumps water from the wa-
ter reservoir into the steam boiler. The filling process
can take several minutes.
ATTENTION
Damage to the device
Unsuitable water can block the nozzles or damage the
water level indicator.
Do not fill in pure distilled water. Use a maximum of 50%
distilled water mixed with tap water.
Do not use condensation from the clothes dryer for filling.
Do not use collected rain water for filling.
Do not use cleaning agents or other additives (e.g.
scents) for filling.
1. Fill the water tank with tap water or a mixture of tap
water and no more than 50% distilled water up to the
"MAX" mark.
The device is ready for use.
Switching off the device
1. Turn the trigger to "OFF” position.
Illustration N
The device is switched off.
2. Set the child lock to the rear.
The steam lever is locked.
3. Push the cap on the device socket down and discon-
nect the steam connector from the device socket.
4. Pull the mains plug out of the socket.
5. Drain the water reservoir.
Rinsing out the steam boiler
Rinse the device’s steam boiler out after every
eighth filling of the tank.
1. Switch the device off; see Chapter
Switching off the
device .
2. Allow the device to cool down.
3. Drain the water reservoir.
4. Remove the accessory/accessories from the acces-
sory holders.
5. Open the cap of the accessory compartment.
6. Remove the accessory/accessories from the acces-
sory compartment.
7. Open the maintenance lock. To do this place the
open end of an extension tube on the maintenance
lock, insert this into the guide so it engages and
open it.
Illustration R
8. Fill the steam boiler with water and swing it around
vigorously. Lime residue which has been deposited
on the bottom of the steam boiler will be released as
a result.
9. Drain the water completely out of the steam boiler.
Illustration S
Storing the device
1. Store the round brush in the accessory compart-
ment.
2. Connect a manual nozzle to one extension tube.
3. Connect the extension tubes to the accessory hold-
ers.
4. Insert the spotlight nozzle in the storage for acces-
sories.
5. Hang the floor nozzle in the park bracket.
Illustration P
6. Wind the steam hose around the extension tube and
connect the steam gun to the floor nozzle.
Illustration Q
7. Store the mains cable in the storage for the mains
cable.
8. Store the device in a dry location that is protected
from frost.
Important application instructions
Cleaning the floor areas
We recommend sweeping the floor or vacuum cleaning
it before using the appliance. In this way the floor will be
cleared of dirt and loose particles before the wet clean-
ing.
Freshening up textiles
Prior to using the appliance, always check the compati-
bility of the textiles at a concealed point: Steam down
the textile, allow it to dry and then check it for any
change in colour or shape.
Cleaning coated or painted surfaces
ATTENTION
Damaged surfaces
Steam can loosen wax, furniture polish, plastic coatings
or paint and edge band from edges.
Do not direct the steam at glued laminated edges as the
edge band may loosen.
Do not use the appliance for cleaning unsealed wood or
parquet floors.
Do not use the appliance for cleaning painted or plastic
coated surfaces such as kitchen or living room furniture,
doors or parquet.
1. To clean these surfaces, steam a cloth briefly and
use it to wipe over the surfaces.
Glass cleaner
ATTENTION
Glass breakages and damaged surfaces
Steam can damage sealed points of the window frame
and, at low outside temperatures, lead to tension on the
surface of window panes and hence to glass breakages.
Do not direct the steam at sealed points on the window
frame.
At low outside temperatures, heat up the window panes
by gently steaming the full surface of the glass.
 Clean the window area with a manual nozzle and
cover. To remove the water, use a squeegee or wipe
the surfaces dry.