background image

(QJOLVK

a Push the 1st extension tube onto the steam gun 

so that the unlocking button on the steam gun en-

gages.

The connection pipe is connected.

b Push the 2nd extension tube onto the 

1st extension tube.

The connection pipes are connected.

Illustration H

4. Push the accessory and / or the floor nozzle onto the 

free end of the extension tube.

Illustration I

The accessory is connected.

Disconnecting accessories

1. Move the child lock back.

The steam lever is locked.

2. Press the unlocking button and pull the parts apart.

Illustration M

Operation

Filling water

The water reservoir can be removed at any time for fill-

ing or be filled directly at the device.

ATTENTION

Damage to the device

Unsuitable water can block the nozzles or damage the 

water level indicator.

Do not fill in pure distilled water. Use a maximum of 50% 

distilled water mixed with tap water.

Do not use condensation from the clothes dryer for fill-

ing.

Do not use collected rain water for filling.

Do not use cleaning agents or other additives (e.g. 

scents) for filling.

Removing the water reservoir for filling

1. Pull the water reservoir vertically upwards.

Illustration B

2. Fill the water tank vertically with tap water or a mix-

ture of tap water and no more than 50% distilled wa-

ter.

3. Insert the water reservoir and press downwards until 

it locks into place.

Filling the water reservoir directly on the device

1. Fill tap water or a mixture of tap water and no more 

than 50% distilled water from a vessel into the filling 

hole of the water reservoir.

Illustration C

Switching on the device

Note

If there is no or too little water in the steam boiler, the 

water pump starts to run and pumps water from the wa-

ter reservoir into the steam boiler. The filling process 

can take several minutes.

Note

The device briefly closes the valve every 60 seconds 

causing an audible soft click. Closing prevents the valve 

from clogging. This does not affect the steam output. 

1. Place the device on a firm surface.

2. Insert the main plug into a socket.

3. Turn the selector switch from the OFF position to the 

steam setting selection range.

Illustration D

The LED strip is in fading red.

4. The LED light lights up a continuous green after ap-

prox. 3 minutes.The device is ready for use.

Illustration E

5. Press the steam lever.

Illustration F

Steam leaks out.

Regulating the steam volume

The expelled steam volume is regulated using the se-

lector switch for steam volume. The selector switch has 

three positions. 

1. Set the selector switch for the steam volume to the 

required steam volume.

2. Press the steam lever.

3. Before cleaning, point the steam gun at a cloth until 

steam is expelled evenly.

Refilling water

If there is not enough water in water reservoir, the LED 

light rapidly flashes red and a signal tone sounds.

Note

The water pump fills the steam boiler at intervals. If the 

filling is successful, the LED light is quick flashing red.

Note

If there is no or too little water in the steam boiler, the 

water pump starts to run and pumps water from the wa-

ter reservoir into the steam boiler. The filling process 

can take several minutes.

ATTENTION

Damage to the device

Unsuitable water can block the nozzles or damage the 

water level indicator.

Do not fill in pure distilled water. Use a maximum of 50% 

distilled water mixed with tap water.

Do not use condensation from the clothes dryer for fill-

ing.

Do not use collected rain water for filling.

Do not use cleaning agents or other additives (e.g. 

scents) for filling.

1. Fill the water tank with tap water or a mixture of tap 

water and no more than 50% distilled water.

The device is ready for use.

Switching off the device

1. Turn the power switch to the "OFF” position.

Illustration L

The device is switched off.

2. Move the child lock back.

The steam lever is locked.

3. Pull the main plug out of the socket.

4. Drain the water reservoir.

Rinsing out the steam boiler

Rinse the device’s steam boiler out after every 

tenth filling of the tank.

1. Switch the device off; see Chapter 

 Switching off the 

device

.

Maximum steam volume

Medium steam volume

Minimum steam volume

Содержание SC 4 Deluxe










Отзывы: