Kärcher B 90 R Adv, Оригинальное руководство пользователя

Страница: 18 / 240

-
6
Figure 22, see cover page
 Insert the cylinder pin into the boring of
the drawbar.
 Slide the drawbar in the guide channel
on the cleaning head all the way to the
bottom.
 Insert the locking plate into the guide
channel and lock it in.
 Repeat process on the drawbar on the
opposite side.
Figure 23, see cover page
 Press in the locking plate and swivel the
drawbar upward.
The subsequent removal will take place in
the opposite order of the installation.
The removal will take place in the opposite
order of the installation.
Figure 24, see cover page
 Lift the cleaning head.
 Loosen the lock of the wiper flap.
 Swivel the wiping flap out of the way.
Figure 25, see cover page
 Loosen the lock of the wiper flap.
 Push the bearing lid down and remove.
 Pull out the brush roller.
 Insert a new brush roller.
 Reattach the bearing lid and the wiper
flap in reverse sequence.
 Repeat process on the opposite side.
 Lift the cleaning head.
 Press the pedal for changing the brush-
es downward beyond its resistance.

Pull the disc brush out of the side below
the cleaning head.
 Hold the new disc brush under the
cleaning head, push upward and lock.
 Unscrew the right stepping platform
and remove along with the drive pedal.
Figure 26, see cover page
1 Covering lid
2 Cover
3 Hose holder
4 Pump hose
5 Rotor
 Remove covering lid.
 Remove cover.
 Remove the hose holder with the pump
hose (turn manually to remove the rotor
manually).
 Replace pump hose.
 Dosing pump and appliance are
brought into operational state by per-
forming the same steps in the reverse
direction.
In case of danger of frost:
 Empty the fresh and dirt water reser-
voirs.
 Store the appliance in a frost-protected
room.
 Danger
Risk of injury! Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Press emergency-stop button.
Place the appliance on a stable, even sur-
face and disconnect the battery.
 Drain and dispose of the dirt water and
the residual fresh water.
In case of faults that cannot be remedied
using the table below please contact the
customer service.
Note:
Defective pole fuses should only be re-
placed by the service center. If these fuses
are defective, then customer service center
has to check the usage conditions and the
entire control system.
If errors appear on the display, then pro-
ceed as follows:
 Set the key switch to "0" (switch off the
machine).
 Wait till the text on the display has dis-
appeared.
 Set the main switch again to "1" (switch
on the machine). Carry out the trouble-
shooting measures in the given se-
quence only if the fault occurs again. At
such times, always bring the main
switch to the "0" position and ensure
that the emergency-stop button is de-
pressed.
 If the fault cannot be repaired, call cus-
tomer service and mention the error
message.
Note:
Fault messages that are not listed in the fol-
lowing table indicate faults that cannot be
rectified by the operator. Please contact the
aftersales service.
Remove D cleaning head
Remove R cleaning head
Replacing the brush rollers
Replacing the Disk Brushes
Replace pump hose (only Dose model)
Frost protection
Troubleshooting
Replace fuses
Fault indication
Faults with display
Display Cause Remedy
E: Did you press the
emergency stop but-
ton !?! Press emergency-stop button. Release emergency-stop button by turning. Set the main switch to "0". Wait un-
til display goes off. Set the main switch back to "1".
E: Pow.module hot
Let cool down! Control is overheated Turn the key switch to "0". Wait at least 5 minutes to let the control cool off.
Turn the appliance back on.
E: Overload
BRUSH Overload on brush motor Set key switch to “0”. Wait for 3 seconds. Turn the appliance back on. Reduce
the brush contact pressure.
E: Hardw. failure
Onboardcharger Interference in the integrated charg-
er (only Pack model) Disconnect the power cord plug of the charger. Wait for 10 seconds. Plug in
the power cord plug. If the error message appears again: Call customer ser-
vice.
E: Failure char- ging
battery Battery defective Check battery.
E: Overload TRAC-
TION MOTOR Drive motor has got overheated due
to a steep climb or locked brake. Allow machine to cool down at least 15 minutes. Set key switch to “0”. Wait for
3 seconds. Turn the appliance back on. Avoid frequent uphill driving.
Seat switch!
Please sit down! Seat contact switch has not been
activated. Release the drive pedal. Have a seat.
Release gaspedal The gas pedal is depressed when
the main switch is on. Release drive pedal and reactivate.
Followup suction
Shutdown shortly The key switch was turned to "0"
while the suction turbine was run-
ning. The suction turbine trails with a delay of 10 seconds. Wait until the appliance
shuts itself off after 10 seconds.
Dirttank full Clean-
ing stops waste water tank is full. Empty the waste water tank.
Emergency brake
operation! Drive at
ground level Parking brake is defective. Danger! Do not drive over upward/downward slopes.
Park the machine on an even surface.
Secure the machine with wheel chock(s) to prevent it from rolling away.
Inform Customer Service.
18 EN