Kärcher B 90 R Adv, Оригинальное руководство пользователя

Страница: 17 / 240

-
5
 Take the dirt water discharge hose from
the support and lower above a suited
collection device.
Figure 11, see cover page
 Let off water by opening the dosage de-
vice at the discharge hose.
 The rinse the dirt water reservoir with
clear water.
 Unscrew the filter cup of the fresh water
filter and let the fresh water tank drain
completely.
 Replace the filter cup.
 Check the waste container. If needed,
remove and empty waste container af-
ter work.
 Turn main key to "0" and remove it.
 Secure the machine with wheel chocks
to prevent it from rolling away.
 DANGER
Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients of max. 10%. Drive slowly.
몇 CAUTION
Risk of injury and damage! Observe the
weight of the appliance when you transport it.
 When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
 Remove brushes from the brush head.
몇
CAUTION
Risk of injury and damage! Note the weight
of the appliance in case of storage.
 This appliance must only be stored in
interior rooms.
 Select the storage site for the appliance
taking into consideration the permissi-
ble total weight of the appliance in order
not to impact its stability.

Danger
Risk of injury. Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Press emergency-stop button.
Place the appliance on a stable, even sur-
face and disconnect the battery.
몇
WARNING
Suction turbine will continue to run for a
while after switch-off. Carry out mainte-
nance tasks only after the suction turbine
has come to a halt.
 Drain and dispose of the dirt water and
the residual fresh water.
ATTENTION
Risk of damage. Do not sluice the appli-
ance with water and do not use aggressive
detergents.
 Drain off dirt water.
 Check the flat folded filter, clean if re-
quired
 Only with R cleaning head Remove bulk
waste container and empty it.
 Clean the outside of the appliance with
a damp cloth which has been soaked in
mild detergent.
 Clean the vacuum lips and the wiping
lips, check for wear and replace if re-
quired.
 Check the brushes for wear, replace if
required.
 Charge the battery:
If the charging state of the battery is un-
der 50%, charge the battery fully and
without interruption.
If the charging state of the battery is
over 50%, only recharge the battery if
the entire operation duration will be re-
quired when next used.
 When used regularly, charge the bat-
tery fully and without interruption at
least once a week.
 Check battery pole for oxidation; brush
it if required and lubricate it using pole
grease. Ensure that the connection ca-
ble sits firmly.
 Clean the seals between waste water
tank and cover and check for tightness,
replace if required.
 Check the acid density of the cells if the
batteries are not maintenance-free bat-
teries.
 Clean the brush tunnel (only R cleaning
head)
Figure 12, see cover page
 Remove the water distribution strip from
the cleaning head and clean water ca-
nal (only R cleaning head).
 For long periods of disuse, only turn the
device off when the battery is fully
charged. Fully recharge the battery at
least every month.
 Replace pump hose of the metering
pump (only Dose model).
 Have the prescribed inspection carried
out by the customer service.
For a reliable operation of the appliance
maintenance contracts can be concluded
with the competent sales/service consult-
ant.
 Remove the vacuum bar.
 Unscrew the star grips.
Figure 13, see cover page
 Remove the plastic parts.
 Remove the vacuum lips.
 Insert new vacuum lips.
 Insert the plastic parts.
 Screw in and tighten the star grips.
 Push the pedal for raising/ lowering the
cleaning head down.
 Slide the cleaning head under the appli-
ance so that the hose points toward the
rear.
Only slide the cleaning head halfway
under the appliance.
Figure 14, see cover page
 Remove the lid of the cleaning head.
Figure 15, see cover page
 Connect the power cord of the cleaning
head to the appliance (same colours
must meet).
 Replace the lid and lock it.
 Slide the cleaning head halfway under
the appliance.
Figure 16, see cover page
 Connect the hose couplers on the
cleaning head to the hose on the appli-
ance.
Figure 17, see cover page
 Insert the tab into the middle of the
cleaning head, between the fork of the
lever.
 Position the lever on the pedal for rais-
ing/lowering so that the borings in the
lever and the cleaning head align.
 Insert the stop pin through the bushings
and swivel the locking plate downward.
Figure 18, see cover page
 Insert the cylinder pin into the boring of
the drawbar.
 Slide the drawbar with the pin the guide
channel on the cleaning head all the
way to the bottom and lock.
 Repeat process on the drawbar on the
opposite side.
 Push the pedal for raising/ lowering the
cleaning head down.

Slide the cleaning head under the appli-
ance so that the hose points toward the
rear.
Only slide the cleaning head halfway
under the appliance.
Figure 19, see cover page

Pull out the cover.
Figure 20, see cover page
 Connect the power cord of the cleaning
head to the appliance (same colours
must meet).
 Push in the cover.

Slide the cleaning head halfway under
the appliance.
Figure 16, see cover page
 Connect the hose couplers on the
cleaning head to the hose on the appli-
ance.
Figure 21, see cover page
 Insert the tab into the middle of the
cleaning head, between the fork of the
lever.
 Position the lever on the pedal for rais-
ing/lowering so that the borings in the
lever and the cleaning head align.
 Insert the stop pin through the bushings
and swivel the locking plate downward.
Emptying the Fresh Water Tank
Empty waste container (only with R
cleaning head)
Shutting down
Transport
With mounted D cleaning head
Storage
Care and maintenance
Maintenance schedule
After the work
Weekly
Monthly
Yearly
Maintenance Works
Maintenance contract
Replacing the vacuum lips
Install D cleaning head
Install R cleaning head
17 EN