Kärcher 1.047-310.0, Руководство пользователя

Страница: 20 / 402

-
4

Danger
Risk of injury, risk of damage!
Observe the weight of the appliance when
you load it!
Do not use a forklift truck to unload the ma-
chine as this may damage it.
 Use a suitable ramp or a crane to load
the appliance!
 If the machine is delivered on a pallet,
you must create an unloading ramp us-
ing the boards provided.
To unload the machine, proceed as follows:
 Cut plastic packing belt and remove foil.
 Connect battery (see section on Care
and maintenance)
 Remove the elastic tape fasteners at
the stop points.

Four indicated floor boards of the pallet
are fastened with screws. Unscrew
these boards.

Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with screws.
 Slide the four support beams included
in the packaging under the ramp.

Remove the wooden blocks used for ar-
resting the wheels and slide them under
the ramp.

Slide the machine over the prepared
ramp from the pallet.
The machine can be moved in 2 ways:
(1) By pushing it (see Moving sweeper
without engaging self-propulsion).
(2) By driving it (see Moving sweeper by
engaging self-propulsion).

Danger
Risk of injury! Before engaging the free-
wheel operation, the machine must be se-
cured to prevent it rolling away.
– The travel drive is inoperable.
– Braking effect exists no more.
CAUTION
Risk of damage to the hydrostatic axle drive!
Only push sweeper slowly and across short
distances.

Open the device hood.
Position of the freewheel lever up - appli-
ance can be pushed.
 Engage the freewheel lever in the upper
position.
Note: If the freewheel lever does not
lock in, then slightly move the machine
forward and backward.
 After moving the appliance, snap the
freewheel lever into the lower position.
 Close cover.
 Open the device hood.
Position freewheel lever down - appliance
is ready to start.
 Engage the freewheel lever in the lower
position.

Close cover.
Note: The machine has been fitted with an
automatic parking brake that is activated as
soon as the engine is switched off and the
driver leaves his seat.
 Park the sweeper on an even surface.
 Remove ignition key.
 Check engine oil level.
 Check the filling level of the fuel tank at
the fuel gauge.
 Check fill level of hydraulic oil.
 Check side brush.
 Check the roller brush for wear and
wrapped belts.
 Empty waste container.
 Check tyre pressure.
 Check function of seat contact switch.
 Check, if the stop switch on the com-
bustion engine is in the "ON" position.
Note: For description, see section on Care
and maintenance.

Danger
Risk of explosion!
– Only fuel up while motor is turned off.
– Only use the fuels specified in the Op-
erations Manual.
– Do not refuel the machine in enclosed
spaces.
– Smoking and naked flames are strictly
prohibited.
– Ensure that no fuel reaches the hot
open surfaces.
1 Tank lid
2 Tank indicator
3 Fuel cock
 Switch off engine.
 Open the device hood.
 Read the filling level at the fuel gauge.
The red area indicates the filling level.
 Open fuel filler cap.
 Use and install a funnel with a filter.
 Use "regular unleaded petrol".
Tank filling with empty tank approx. 5 li-
tre
 Wipe off any spilt fuel, remove funnel
and close fuel filler cap.
 Close cover.
CAUTION
Risk of damage to the drive! Prior to each
run, ensure that the freewheel lever is in the
lower position.
CAUTION
The air inlets next to the driver's seat must
not be covered. Do not store any objects
next to or behind the seat.
 Pull seat adjustment lever inwards.
 Slide seat, release lever and lock in place.
 Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
Note: The max. load of the storage area is
20 kg.
 Ensure safe fastening of the cargo.
Unloading tips
Net weight (transport weight) 265 kg *
* If upgrade kits are installed, the weight is
respectively higher.
Moving sweeper without engaging
self-propulsion
Moving sweeper by engaging self-
propulsion
Start up
General notes
Prior to start/safety test
Maintenance Works
Refuelling
Operation
Adjusting driver's seat
Storage area
20 EN