Kantronics KAM Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 80

Kantronics KAM Скачать руководство пользователя страница 57

Chapter 7 - Commands and Messages

57

KIssmode

ON|OFF

default OFF

When in the KISS Mode, the KAM will use the KISS protocol as specified by PHIL KARN. There

are two ways to enter the KISS Mode. In both cases, you must first turn the

KIssmode

parameter

ON by typing

KI ON

while in Command Mode. Now any command which will cause a soft reset,

e.g. RESET, MAXUSER, PBBS, etc., will put the KAM in KISS Mode. Turning the KAM off and then
on will cause the KAM to return to Command Mode. The other method of entering KISS Mode is to
first turn

KIissmode

ON and then

PErm

the value in EEPROM; be sure to also

PErm ABaud

to a

nonzero value. Now when the unit is turned ON it will automatically be in KISS Mode. If KISSMODE
is permed ON, the only way to turn off KISS is to either reset all the EEPROM values using the
TEST/NORMAL jumper, or use the special KISS command in TCP/IP to get back into Command
Mode. If the special KISS command is used, the KAM would have its KISSMODE parameter turned
off but the EEPROM parameter is still turned on until KISSMODE is permed off.

Lamtor

This command sets the unit in listen AMTOR Mode. The unit will receive either FEC or ARQ sig-

nals. The selcall being used by a station sending ARQ phasing signals may also be decoded when
in this mode. Such calls will appear on the display as the same four letter group appearing repeti-
tively on the display.

LCok

ON|OFF

default ON

When ON, no character translation occurs in the KAM. If OFF, lower case characters will be

translated to upper case before being output to the terminal from the KAM. This case translation is
disabled in packet Transparent Mode.

LCRtty

ON|OFF

default OFF

When ON, lower case characters can be sent and received in RTTY and AMTOR Modes. If you

are sending lower case RTTY, the other station will print lower case RTTY only if its

LCRtty

parame-

ter is also ON. This is accomplished by using the RTTY null character as a special shift character;
this is the same method used in RTTY to send the Russian Cyrillic alphabet. If

USOs

is ON, a re-

ceived space will cause a shift to the lower case.

LCStream

ON|OFF

default ON

When ON, the KAM allows for lower-case characters to be used in stream switching.

LFadd

ON|OFF

default OFF

When ON, a linefeed character (LF) is added after each CR sent to the radio.

LList

ON|OFF

default OFF

When ON,

SUPCalls

stations attempting to connect to or digipeat through your station will be

ignored.

LOwtones

ON|OFF

default OFF

When ON, the European low-tones are used with 170, 425, or 850 shift RTTY. These are:

Mark=1275 Hz, Space=1445 Hz, 1700 Hz or 2125 Hz.

MAll

ON|OFF

default ON/ON

When ON, monitored packets include both "connected" and "unconnected" packets. If OFF, on-

ly "unconnected" packets will be monitored. If

MAll

is OFF, only otherwise eligible packets (as de-

termined by

BUdlist

and

SUplist

commands) sent by other stations in the unconnected mode will

be displayed. This is a useful arrangement when stations are talking as a group in an unconnected
configuration.

«
...
55
56
57
58
59
...
»

Содержание KAM

















































































Отзывы:

Нет отзывов