Kantech IP Link Скачать руководство пользователя страница 28

Страница: 28 / 37

DN1670-1609

6. From the

Options

menu, select

System Parameters

7. From the

Firmware

section, click on the

IP Link

tab.

8. Make sure the

Enable TFTP IP Link updater

option is checked.

9. Click on the 3 dots to locate the firmware file.
10.Select the firmware file and click

11. Click

to close the

System Parameters

dialog.

12.From the

Operation

menu, select

Site

13.Select the Gateway from the

Gateway List

Note:

For the EntraPass Special Edition application, there is no

Gateway List

selection.

14.Click on the site that corresponds to the IP Link to highlight it.
15.Click on the reload firmware button.

16.A confirmation will display.

17.Click

Yes

18.The IP Link will reset and restart with the new firmware.

Warning:

That process could take up to 5 minutes.

The communication status in the

Operation

Site

will say

IP Link Communication Failed

then back

IP Link Communication OK

Содержание IP Link






































Результаты поиска

Содержание IP Link

Отзывы:

Похожие инструкции для IP Link

Бренды по названию

Популярные бренды

Kantech IP Link, Руководство по установке

Результаты поиска

Содержание IP Link

Отзывы:

Похожие инструкции для IP Link

Бренды по названию

Популярные бренды