manualshive.com logo in svg

KANGKE INDUSTRIAL Monocoupe 90A, Инструкция по сборке

Поделиться
Скачать
KANGKE INDUSTRIAL Monocoupe 90A Скачать руководство пользователя страница 8

Drill a 1/8-inch hole in the elevator on both 
sides of the rudder at the location shown for 
the control horns. 

 

8

Control horns come in three different 
lengths, for the elevator halves use two 
“Short” horns and screws. 

Install the control horns in the elevator 
halves. 

Drill a 1/8-inch hole for the rudder horns at 

the location shown. 
 
Use two “Medium” length horns and the 

threaded center link for the rudder 
Assemble the rudder horns as shown. 

 
 
 
 
SERVOS / CONTROLS 
The Monocoupe was designed to use 
standard servos with 40 ounce-inches of 
torque for the elevator, ailerons and flaps. 
The proto-type flies using Hitec HS-425BB 
for all controls except the rudder. For the 
rudder we recommend the Hitec HS-
625MG, the use of the metal gear servo is 
necessary to handle steering loads during 
take off and landing. Because of the large 
assortment of radios and servos on the 
market this section should only be used as a 
basic guide for installation and not as a 
replacement for the servo / radio 
manufactures instructions.  

Содержание Monocoupe 90A


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды