manualshive.com logo in svg

KANGKE INDUSTRIAL Monocoupe 90A, Инструкция по сборке

Поделиться
Скачать
KANGKE INDUSTRIAL Monocoupe 90A Скачать руководство пользователя страница 12

With everything hooked up to the engine 
install the cowl, propeller and spinner. The 
front is now finished. 

 
Double check to be sure the landing gear 
bolts are tight. Install the belly pan on the 
fuselage with the provided screws. 

 
Install the landing gear fuselage fairing pair. 
Be sure the notch is over the wing strut-
attaching hole. Use canopy adhesive and 
tape in place till dry. 
 

 

Assemble the wheels/axel. Slide the axel 
through the wheel, slide on a collar followed 
by a nut and washer. Adjust the collar and 
nut till there is 1/8-inch side play for the 
wheel. hold the two washers and locknut for 
instalation in the pants. 

 
Install the rotation stop screw and lock nut 
through the wheel pant and landing gear. 
Slide a washer on the axle and gently spread 
the pant to insert the assembly. Secure with 
another washer and the lock nut. 

Using canopy adhesive secure the wheel pant 
fairing to the wheel pants. 

 

 

12

Содержание Monocoupe 90A


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды