18
I General User Manual
9.3.5 Adjusting the handlebar height with an
adjustable handlebar stem
With some types of handlebar stems, you can vary the
handlebar tilt. The stem angle can be adjusted via the
clamping screws which are on the side of the articulation
or the top/bottom of the stem. Models equipped with ad-
ditional stop notches or adjusting screws are available.
Hexagon socket screw
(integrated stop notch)
Adjusting screw
Adjust the handlebar tilt as follows:
›
Undo the clamping screw by turning it anticlock-
wise through two or three revolutions using an
Allen key.
›
If you own a model that is also equipped with
detents, continue turning the clamping screw anti-
clockwise to disengage the detents.
›
If you own a model with integrated stop notch,
loosen the screw of the stop notch. In many stem
types this is located on the underside of the stem.
›
Tilt the handlebar stem to the required angle.
›
To fasten the handlebar stem, tighten the clamping
screw clockwise using an Allen key . If tightening
torques are specified on the stem, use exactly these
torques, and if not, refer to the table of tightening
torques in
.
›
In models with an integrated stop notch, tighten
the screw of the stop notch carefully clockwise.
In doing so, the stop notch must engage with the
teeth.
10 Frame
The form of the frame depends on the bike type and func-
tion. Frames are manufactured from different materials
– steel or aluminium alloys or carbon (carbon fibre), for
example.
The frame number of the bike is stamped on the seat
tube, the dropout or the bottom bracket housing.
It may also be found on the motor suspension in Pe-
delecs. The bike can be identified by the frame num-
ber if it is stolen. To identify the bike properly, it is
important to note down the whole number in the right
order.
Never ride your bike if the frame is warped or
cracked. On no account should you attempt to repair
damaged parts. This can lead to accidents. Replace
defective parts before you ride the bike again.
After an accident or crash, have your bike checked by
a professional bike workshop before riding it again. If
defects on the frame or components go unnoticed this
can lead to accidents.
If your bike does not roll forwards easily in a straight
line, this could mean that the frame is warped. In this
case, have the steering stability checked by a profes-
sional bike workshop.
Содержание Bosch Cruise
