V User Manual Impulse Pedelec
9
1 Quick start
›
1. Charge the battery completely before riding for
the first time. Charge temperature: 0 – 45°C
›
2. Swivel the round charging socket cover on the
battery to one side.
Now insert the four-pole plug of the charger into
the battery charging socket.
Charging the battery
›
3. Insert the mains plug for the charger into the
socket.
You must fully charge the battery before using it for
the first time.
›
4. Once all LEDs on the battery have gone out, pull
the charger plug out of the battery socket. Swivel
the cover back over the charging socket.
You can also remove the battery from your Pedelec
and charge it in the docking station. For more infor-
mation, refer to
➠
Chapter 4 “Charging the battery”
.
›
5. If you have charged the battery in the docking
station, reinsert the battery into the holder on the
Pedelec from the left-hand side. Tilt the battery
outwards at an angle of roughly 45° as you do so,
as you did when you took it out of the holder. Move
the battery into the upright position until the lock-
ing mechanism engages. If the key is still in the
lock, you will need to turn it clockwise and pull it
out as otherwise the battery will not lock in place.
›
6. Make sure that the battery is securely posi-
tioned and that the key is no longer in the lock.
If your Pedelec is equipped with an LCD control
panel:
›
7. Push the Power button on the control panel on
the handlebar.
›
8. The display panel now displays the medium
power-assist mode
SPORT
. Press the arrow but-
tons to select the level of assistance:
STAND BY
(off),
ECO
(low),
SPORT
(medium) or
POWER
(high).
Press this button once to change the level of assis-
tance by one level. This works both ways, depend-
ing on which arrow button you press.
The following applies for bikes which are equipped
with a back-pedal brake:
›
9. The system will now perform a system check.
“Please move the pedals” will appear on the
screen. If you set off now the system will normally
detect a pedal movement in the “drive” and “back-
pedal brake” directions. This completes the safety
check, and you can ride as normal with assistance.
If you cannot feel any assistance, simply back-pedal
briefly and then pedal forwards again to trigger the
system check. If there is still no assistance being
delivered, the instruction “Please move the
pedals” will continue to be displayed. In this case
you should consult a specialist dealer.
You can now ride off just as you would if you were
riding a normal bike. The motor starts providing
assistance as soon as the rear wheel starts turning.
Содержание Bosch Cruise
