Kaleidescape M700 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

Kaleidescape M700 Скачать руководство пользователя страница 9

KVAULT ODD Replacement

December 2020

101-0269-00 Rev 2

Page 9 of 24

3.

On the other side of the drive, use the Philips screwdriver to remove

the 2 self-retaining mounting screws. See Figure 12.

Figure 12

4.

Remove the disc drive and attached mounting brackets from the unit.

Mark the drive as defective, to avoid accidental reuse.

5.

Check the defective drive for stuck discs and carefully extract any

disc if found. Removing the drive bezel can help with this.

Transfer Mounting Brackets to New Optical Disc Drive

1.

On the removed optical disc drive, note the orientation of the bottom

bracket in relation to the optical drive.

2.

Remove the two screws from the bottom bracket and recover the

bracket.

3.

Attach the recovered bottom mounting bracket to drive with two of

the provided M2 screws with a 1.5mm hex screwdriver. These screws

are threaded into the soft aluminium of the drive housing and only

require a gentle tightening.

«
...
7
8
9
10
11
...
»

Содержание M700

























Отзывы:

Нет отзывов