Kaisai KPPD Series, Руководство пользователя

Страница: 57 / 114

SCALE 0.500
SCALE 0.500
Operation
Water drainage
-During dehumidifying modes, remove the upper drain
plug from the back of the unit, install the drain connector
(5/8" universal female mender) with 3/4" hose(locally
purchased). For the models without drain connector, just
attach the drain hose to the hole. Place the open end of
the hose directly over the drain area in your basement
floor.
WAIT 3 MINUTES BEFORE RESUMING OPERATION
After the unit has stopped, it can not be restarted
operation in the first 3 minutes. This is to protect the unit.
Operation will automatically start after 3 minutes.
POWER MANAGEMENT feature(on some models)
When the ambient temperature is lower than the setting
temperature for a period of time, the unit will be
automatically operate power management feature. The
compressor and fan motor stop. When the ambient
temperature is higher than the setting temperature, the unit
will be automatically quit the power management feature.
The compressor and (or) fan motor run.
NOTE: For unit with power management light, the light
will illuminate under this feature.
-During heating pump mode, remove the lower drain plug
from the back of the unit, install the drain connector(5/8"
universal female mender) with 3/4" hose(locally
purchased). For the models without drain connector, just
attach the drain hose to the hole. Place the open end of
the Hose adaptor directly over the drain area in your
basement floor.
NOTE: Make sure the hose is secure so there are no
leaks.Direct the hose toward the drain, making sure that
there are no kinks that will stop the warter flowing.Place
the end of the hose into the drain and make sure the end
of the hose is down to let the water flow smoothly.(See
Figs with . Do never let it up.(See Figs with ). When
the continuous drain hose is not used, ensure that the
corresponding drain plug and knob are installed firmly to
prevent leakage.
√ X
Maintenance
-Always unplug the unit before cleaning or servicing.
-DO NOT use flammable liquids or chemicals to clean the unit.
-DO NOT wash the unit under running water. Doing so
causes electrical danger.
-DO NOT operate the machine if the power supply was damaged
during cleaning. A damaged power cord must be replaced with a
new cord from the manufacturer.
Clean the Air Filter
Remove the air filter
Upper filter
(take out)
Remove the
screw,then
take the lower
filter out.
WARNING:
MODEL A
MODEL B
MODEL A MODEL B
MODEL A
MODEL B
15
√
drain hose
adaptor
Continuous
drain hose
Remove the
lower drain plug
√
drain hose
adaptor
Continuous
drain hose
Remove the
lower drain plug
SCALE 0.500
Remove the
upper drain plug
√
Continuous
drain hose
Remove the
upper drain plug
√
Continuous
drain hose
Uper air filter
(take out)
Lower air filter
(take out)
SCALE 0.500
SCALE 0.500
SCALE 0.500
X
drain hose
adaptor
Press the power
cord buckle into
the rear cover.
drain hose
adaptor
√
delivery lift <1.8m
-When the water level of the bottom tray reaches a
predetermined level, the unit beeps 8 times, the digital
display area shows "P1" . At this time the air
conditioning/dehumidification process will
immediately stop. However, the fan motor
will continue to operate(this is normal).
Carefully move the unit to a drain location,
remove the bottom drain plug and let the
water drain away. Reinstall the bottom
drain plug and restart the machine until
the "P1" symbol disappears. If the error repeats, call for
service. NOTE: Be sure to reinstall the bottom drain plug
firmly to prevent leakage before using the unit.
CAUTION
DO NOT operate the unit without filter because dirt
and lint will clog it and reduce performance.
Maintenance
16
Please check the machine according to the following form before asking for maintenance:
Faults Diagnosis
Problem
Possible Cause
P1 Error Code
In COOL mode: room
temperature is lower than
the set temperature
The air filter is blocked with
dust or animal hair
The unit is low on
refrigerant
Temperature setting is too
high
The windows and doors in
the room are open
The room area is too large
Troubleshooting
Reset the temperature
Unit does not turn
on when pressing
ON/OFF
button
Unit does not cool
well
The unit is noisy
and vibrates too
much
The unit makes a
gurgling sound
Exhaust hose is not
connected or is blocked
The Water Collection Tray is full.
Turn off the unit, drain the water
from the Water Collection Tray
and restart the unit.
There are heat sources
inside the room
Turn off the unit and clean the
filter according to instructions
Call a service technician to inspect
the unit and top off refrigerant
Decrease the set temperature
Make sure all windows and doors
are closed
Double-check the cooling area
Turn off the unit, disconnect the
hose, check for blockage and
reconnect the hose
Remove the heat sources if
possible
The ground is not level
Place the unit on a flat, level
surface
The air filter is blocked with
dust or animal hair
Turn off the unit and clean the
filter according to instructions
This sound is caused by the
flow of refrigerant inside
the unit
This is normal
Maintenance Tips
Clean the Unit
Store the unit when not in use
-Be sure to clean the air filter every 2 weeks for optimal performance.
-The water collection tray should be drained immediately after P1
error occurs, and before storage to prevent mold.
-In households with animals, you will have to periodically wipe down
the grill to prevent blocked airflow due to animal hair.
Clean the unit using a damp, lint-free cloth and mild
detergent. Dry the unit with a dry, lint-free cloth.
-Run the appliance on FAN mode for 12 hours in a warm room to
dry it and prevent mold.
-Turn off the appliance and unplug it.
-Clean the air filter according to the instructions in the previous
section. Reinstall the clean, dry filter before storing.
-Remove the batteries from the remote control.
-Drain the unit’s water collection tray according to the instructions in
the following section.
Be sure to store the unit in a cool, dark place. Exposure to direct
sunshine or extreme heat can shorten the lifespan of the unit.
NOTE: The cabinet and front may be dusted with an oil-free
cloth or washed with a cloth dampened in a solution of
warm water and mildliquid dishwashing detergent. Rinse
thoroughly and wipe dry. Never use harsh cleansers, wax
or polish on the cabinet front. Be sure to wring excess
water from the cloth before wiping around the controls.
Excess water in or around the controls may cause
damage to the unit.
EN
57