background image

 Page 23 

If you will install the unit on a wall-mounted 
bracket

, do the following:

 CAUTION

Before installing a wall-mounted unit, make 
sure that the wall is made of solid brick, 
concrete, or of similarly strong material. 

The 

wall must be able to support at least four 

times the weight of the unit.

1.   Mark the position of bracket holes based on 

dimensions in the Unit Mounting Dimensions 
chart.

2.   Pre-drill the holes for the expansion bolts.
3.   Clean dust and debris away from holes.
4.   Place a washer and nut on the end of each 

expansion bolt.

5.   Thread expansion bolts through holes in 

mounting brackets, put mounting brackets 
in position, and hammer expansion bolts into 
the wall.

6.   Check that the mounting brackets are level.
7.   Carefully lift unit and place its mounting feet 

on brackets.

8.   Bolt the unit firmly to the brackets.

TO REDUCE VIBRATIONS OF WALL-
MOUNTED UNIT

If allowed, you can install the wall-mounted 
unit with rubber gaskets to reduce vibrations 
and noise.

Step 4: Connect signal and power cables

The outside unit’s terminal block is protected by 
an electrical wiring cover on the side of the unit. 
A comprehensive wiring diagram is printed on 
the inside of the wiring cover.

BEFORE PERFORMING 
ELECTRICAL WORK, 

 

READ THESE REGULATIONS

1.   All wiring must comply with local and 

national electrical codes, and must be 
installed by a licensed electrician.

2.   All electrical connections must be made 

according to the Electrical Connection 
Diagram located on the side panels of the 
indoor and outdoor units.

3.   If there is a serious safety issue with the 

power supply, stop work immediately. Explain 
your reasoning to the client, and refuse 
to install the unit until the safety issue is 
properly resolved.

4.   Power voltage should be within 90-100% of 

rated voltage. Insufficient power supply can 
cause electrical shock or fire.

5.   If connecting power to fixed wiring, install a 

surge protector and main power switch with 
a capacity of 1.5 times the maximum current 
of the unit.

6.   If connecting power to fixed wiring, a switch 

or circuit breaker that disconnects all poles 
and has a contact separation of at least 1/8in 
(3mm) must be incorporated in the fixed 
wiring. The qualified technician must use an 
approved circuit breaker or switch.

7.   Only connect the unit to an individual branch 

circuit outlet. Do not connect another 
appliance to that outlet. 

8.   Make sure to properly ground the air 

conditioner.

9.   Every wire must be firmly connected. Loose 

wiring can cause the terminal to overheat, 
resulting in product malfunction and possible 
fire.

10.  

Do not

 let wires touch or rest against 

refrigerant tubing, the compressor, or any 
moving parts within the unit.

11.  If the unit has an auxiliary electric heater, it 

must be installed at least 1 meter (40in) away 
from any combustible materials.

Outdoor Unit 

Installation

23

kaisai.com

Содержание FIREWIND Series





































Отзывы: