background image

 Page 14 

 CAUTION

Be extremely careful not to dent or damage the piping while bending them away from the unit. Any 
dents in the piping will affect the unit’s performance.

Step 4: Prepare refrigerant piping

The refrigerant piping is inside an insulating 
sleeve attached to the back of the unit. You must 
prepare the piping before passing it through the 
hole in the wall. Refer to the 

Refrigerant Piping 

Connection

 section of this manual for detailed 

instructions on pipe flaring and flare torque 
requirements, technique, etc.
1.   Based on the position of the wall hole relative 

to the mounting plate, choose the side from 
which the piping will exit the unit. 

2.   If the wall hole is behind the unit, keep the 

knock-out panel in place. If the wall hole is to 
the side of the indoor unit, remove the plastic 
knock-out panel from that side of the unit. 
(See 

Fig. 3.3

). This will create a slot through 

which your piping can exit the unit. Use 
needle nose pliers if the plastic panel is too 
difficult to remove by hand.

Knock-out Panel

3.   Use scissors to cut down the length of the 

insulating sleeve to reveal about 15cm (6in) 
of the refrigerant piping. This serves two 
purposes:

  To  facilitate the 

Refrigerant Piping 

Connection

 process

  To  facilitate Gas Leak Check

and enable 

you to check for dents

4.   If existing connective piping is already 

embedded in the wall, proceed directly to 
the 

Connect Drain Hose

 step. If there is no 

embedded piping, connect the indoor unit’s 
refrigerant piping to the connective piping 
that will join the indoor and outdoor units. 
Refer to the 

Refrigerant Piping Connection

 

section of this manual for detailed instructions.

5.   Based on the position of the wall hole 

relative to the mounting plate, determine the 
necessary angle of your piping.

6.   Grip the refrigerant piping at the base of the 

bend. 

7.   Slowly, with even pressure, bend the piping 

towards the hole. 

Do not

 dent or damage the 

piping during the process.

NOTE ON PIPING ANGLE

Refrigerant piping can exit the indoor unit from 
four different angles:

• 

Left-hand side

• 

Left rear

• 

Right-hand side

• 

Right rear

Refer to 

Fig. 3.4

 for details.

Fig. 3.3

Fig. 3.4

Indoor Unit 

Installation

14

kaisai.com

Содержание FIREWIND Series





































Отзывы: