background image

4

Kaden Installer's Manual

Ducted Gas Heaters

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, 

property damage, personal injury and/or death.

WARNINGS:

WHEN IGNORED, CAN RESULT IN SERIOUS INJURY OR DEATH.

CAUTIONS:

WHEN IGNORED, CAN RESULT IN MINOR INJURY OR PRODUCT DAMAGE.

SHALL / MUST/

IMPORTANT: 

INDICATES A MANDATORY REQUIREMENT OF THIS MANUAL.

SHOULD:

INDICATES A RECOMMENDED REQUIREMENT OF THIS MANUAL.

Any deviations from these instructions may void the warranty. As a result, the 

customer and/or installer may be charged a fee for product non-warranty related call 

outs. Also, note that failure to comply with these instructions may preclude servicing 

of the unit.

DISCLAIMER:

This document is a guide only. Laws, regulations and industry standards can vary 

between States and Territories. Accordingly, this guide 

MUST BE

 read in conjunction 

with, and subject to, all laws, regulations and industry standards applicable in the 

State or Territory in which the products are installed. You 

MUST

 ensure that the 

installation of the products will comply with those laws, regulations and standards, 

and that the products recommended to customers are fit for the purpose for which 

they are intended.

WARNING

REGULATORY / INSTALLATION / SAFETY

This appliance 

SHALL BE

 installed in accordance with:

Manufacturer’s Installation Instructions and the Kaden Sizing Guide.
Current AS/NZS 5601 (Gas Installation Standard) and Current AS/NZS 3000 (Electrical Codes) and 

Local Gas / Electrical authority regulations.
Current AS 4254 Ductwork for air-handling systems in buildings, EPA guidelines and HB276-2004 

“A Guide to Good Practice”
Local Regulations and Municipal Building Codes (BCA) including local OH&S requirements.

ALWAYS 

comply with the following precautions to avoid dangerous situations and to ensure optimum 

performance.

This appliance 

MUST BE

 installed, maintained and removed by an Authorised Person.

DO NOT

 place any articles on or against this appliance

DO NOT

 use or store flammable materials near this appliance

DO NOT

 spray aerosols in the vicinity of this appliance while it is in operation

DO NOT

 modify this appliance

This appliance is 

NOT

 intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 

supervision or instruction concerning use of the appliance by a person responsible for their safety
Children should be supervised to ensure that they 

DO NOT 

play with the appliance.

 

IMPORTANT

WARNINGS AND IMPORTANT INFORMATION

Содержание KU5









































Отзывы: