Kaba Mas High Security Pedestrian Exit Device with Electric Locking Trim Скачать руководство пользователя | Manualshive

Страница: 28 / 35

background image

24

Attach Back Cover Assembly for Testing

1.

Install the back cover assembly with the two mounting screws in order to test the operation of the lock.

Do

not install the cover lock pin at this time.

Caution:

Take care to align the connectors and the baffle to the hole in the cover.

2.

Verify the operation of the lock as described on the following page under

INSTALLATION COMPLETION

CHECKLIST.

3.

Check the operation of the lock by verifying the following:
•

Ensure that the dial turns freely without scraping or binding.

•

Ensure that all screws have been securely tightened.

•

Dial the combination (it has been factory set to 50-LEFT, 25-RIGHT, 50-LEFT). Your lock should dial
freely without scraping or rubbing and should open when the correct combination has been dialed.

Final Installation of the Back Cover Assembly

WARNING:

Failure to verify that the lock is operational before installing the cover lock pin assembly may

cause a lock out condition.

1.

Open the lock. Leave the bolt in the fully retracted position and remove the back cover assembly.

2.

Insert the cover lock pin through the back cover.

3.

Install the cover lock spring and retainer clip onto the cover lock pin.
The “fingers” of the retainer clip should be angled away from the cover
lock spring, and the retainer clip must be seated in the groove of the
cover lock pin.

Helpful Hint:

A small hammer and the cut off piece from the inner tube

can be used to install the spring and clip.

Caution:

Do not push the clip retainer past the small groove in the cover

lock pin. If the clip is not located in the pin groove, it can interfere
with pulling the bolt or prevent withdrawal of the pin for normal
back cover removal.

4.

Record the lock serial number in a secure location.

5.

Make sure the bolt is fully retracted and reinstall the back cover with the cover lock pin in place.

Caution:

Take care to align the connectors, the baffle to the hole in the cover, and the cover lock

pin to the keyhole slot in the bolt rack.

6.

Tighten the mounting screws to the specified torque.

7.

After restoring the bolt to the extended position, verify that the cover lock pin is fully recessed into the back
cover. If not, gently wiggle the cover lock pin to seat it.

Lock On Back

Cover Pin

Retainer

Clip

Cover Lock

Spring

Back Cover Assembly

«
...
26
27
28
29
30
...
»

Содержание High Security Pedestrian Exit Device with Electric Locking Trim




































Отзывы:

Нет отзывов

Похожие инструкции для High Security Pedestrian Exit Device with Electric Locking Trim

3007 Direct Drive

Бренд: Sargent and Greenleaf Страницы: 12

Бренд: M-LOCKS Страницы: 4

Бренд: Soyal Страницы: 11

Бренд: COMPX Страницы: 1

Бренд: Trine Страницы: 2

SmartLocker AX SmartIntego

Бренд: Simons Voss Technologies Страницы: 53

Бренд: Dormakaba Страницы: 50

Adhesive Magnet Lock

Бренд: Qdos Страницы: 12

National CB-250

Бренд: COMPX Страницы: 1

HomeTec Pro CFS3100

Бренд: Abus Страницы: 31

Weiser 62884 / 01

Бренд: Spectrum Страницы: 2

ADVANTEX 30 Series

Бренд: Detex Страницы: 7

ADVANTEX 70 Series

Бренд: Detex Страницы: 20

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 4

Бренд: Abus Страницы: 6

Бренд: M&C Страницы: 7

Бренд: Pado Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды