36
When power is interrupted (disconnection, power failure, etc.) in the Record mode or Sensor Record Standby mode, the
recording information on the hard disk may be damaged. This may cause problems in recording and playback.
To repair the hard disk, two disk scan functions (<AUTO SCANDISK> and <MANUAL SCAN DISK>) are available.
●
<AUTO SCANDISK>
If <AUTO SCANDISK> is set to “ON”, the disk is scanned automatically whenever the power is turned on or restored. To cancel
disk scanning, press the [CLOCK RESET/CLEAR] button.
●
<MANUAL SCAN DISK>
Execute <MANUAL SCAN DISK> from the menu. This cannot be canceled once it has been started. Do not turn the power
OFF while this operation is in progress. When <AUTO SCANDISK> is set to “OFF” and the power is kept turned on for long-
time recording, be sure to execute <MANUAL SCAN DISK> regularly.
It is recommended to perform <MANUAL SCAN DISK> once a month if recording is executed continuously.
8 HARD DISK CONTROL
8-1 Hard disk maintenance
Scan the disk when the power is ON.
1. Display the [UTILITY] screen.
Display the [UTILITY] screen in the main menu
[SYSTEM/LIST]. For details, refer to “Setting” on page 18.
2. Set the menu switches.
Set the cursor to [AUTO SCAN DISK] with [JOG ] and
set to “ON” with [JOG – +].
When the setting is complete, press the [MENU] button
twice to restore the normal screen.
When the power is turned ON, the disk is scanned and
the "SYSTEM LOADING
**
%" message is displayed.
Scanning progress is indicated in percentage. When disk
scanning is complete, the % indication goes out.
“LoAd --” blinks on the display panel.
Scan the disk manually.
1. Display the [UTILITY] screen.
Display the [UTILITY] screen in the main menu
[SYSTEM/LIST]. For details, refer to “Setting” on page 18.
2. Set the menu switches.
Set the cursor to [MANUAL SCAN DISK] with [JOG ]
and set to “ON” with [JOG – +].
“EXECUTE: PRESS
£
BUTTON” is displayed on the
monitor.
Reference:
“5-3 Menu switch details” on page 21.
3. Scan the disk.
Press the [SKIP SEARCH·EXECUTE] button to start
scanning the disk.
“SCAN DISK
**
%” is shown on the monitor.
Scanning the disk
f
f
Caution:
●
Disk scanning can take up to 3 hours if the hard disk
contains a lot of data.
Jog dial
Shuttle search dial
[SKIP SEARCH·EXECUTE] button
[MENU] button
[ S Y ST E M ]
[ L I S T ]
U T I L I T Y
B
G
0
8
]
OG
J
[
HOUR ME T E R
POWER LO S S
L I S T
[ U T I L I T
]
Y
1 . A UT O S C
N D I S K
A
S C
N D I S K
A
ON
O F F
O F F
S T D
2 . MAN UA L
3 . Q U I C K
E R AS E
OG
J
C U R R E N T
FO R MAT
E X E C U T E : P R E S S
B U T T O N
+
2.
PLAY
STILL
CANCEL
DISPLAY
MENU
SEARCH
SELECT
REV
FWD
EXECUTE
SKIP/ALARM
SEARCH
REC
CLOCK RESET/ CLEAR
OPE. LOCK
ON
DIGITAL VIDEO RECORDER VR-510U
[CLOCK
RESET/CLEAR]
button
1.
VN
S
Memo:
●
Even if <AUTO SCANDISK> is set to "OFF", "SYSTEM
LOADING
**
%" may be displayed when the power is
turned ON.
