JVC UX-L36V страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 89

background image

1-21

UX-L46V/UX-L36V

Adjustment method

Measurement Instruments Required for

Adjustment

1. Low frequency oscillator
This oscillator should have a capacity to output
0dBs to 600

at an oscillation frequency of

50Hz-20kHz.
2. Attenuator impedance : 600
3. Electronic voltmeter
4. Distortion meter
5. Frequency counter
6. Wow & flutter meter
7. Test tape
  VT703L : Head azimuth
  VT712 : Tape speed and running unevenness
(3kHz)
  VT724 : Reference level (1kHz)
8. Blank tape
  TYPE

: AC-225

TYPE

: AC-514

9. Torque gauge : For play and back tension
FWD(TW2111A), REV(TW2121a) and
FF/REW(TW2231A)
10. Test disc: CTS-1000

Radio Input signal

AM frequency --------------------------------------- 400Hz
AM modulation ---------------------------------------- 30%

FM frequency --------------------------------------- 400Hz

FM frequency deviation ------------------------ 22.5kHz

Tuner section

FM tuning range: 87.5MHz

108.00MHz

AM tuning range:

At 9kHz intervals: 531kHz

1,710kHz

At 10kHz intervals: 530kHz

1,710kHz

Voltage applied to tuner +B : DC5.7V
VT : DC 12V
Reference measurement
output 26.1mV(0.28V)/3
Input positions AM : Standard loop antenna
FM : TP1 (hot) and TP2 (GND)

Standard measurement position of volume

Function switch to Tape
Beat cut switch to Cut
Super Bass/Active hyper Bass to OFF
Bass Treble to Center
Adjustment of main volume to reference output
VOL : 28

Precautions for measurement

1. Apply 30pF and 33k

to the IF sweeper output

side and 0.082

F and 100k

in series to the

sweeper input side.
2. The IF sweeper output level should be made as
low as possible within the adjustable range.
3. Since the IF sweeper is a fixed device, there is no
need to adjust this sweeper.
4. Since a ceramic oscillator is used, there is no need
to perform any MIX adjustment.
5. Since a fixed coil is used, there is no need to adjust
the FM tracking.
6. The input and output earth systems are separated.
In case of simultaneously measuring the voltage in
both of the input and output systems with an
electronic voltmeter for two channels, therefore, the
earth should be connected particularly carefully.
7. In the case of BTL connection amp., the minus
terminal of speaker is not for earthing. Therefore, be
sure not to connect any other earth terminal to this
terminal. This system is of an BTL system.
8. For connecting a dummy resistor when measuring
the output, use the wire with a greater code size.
9. Whenever any mixed tape is used, use the band
pass filter (DV-12).

Measurement conditions

Power supply voltage
AC110V/127V/220V/230V

240V , adjustable

Reference output : Speaker : 0.775V/4
: Headphone : 0.077V/32
Reference frequency and
input level ------------------------------ 1kHz, AUX : -8dBs
Measurement output terminal ------- at Speaker J3002

Load resistance --------------------------- 4

«
...
19
20
21
22
23
...
»

Содержание UX-L36V


























































































Отзывы:

Нет отзывов

Похожие инструкции для UX-L36V

Бренд: KEF Страницы: 6

Бренд: Daewoo Страницы: 66

Бренд: Bandit Страницы: 3

Бренд: BAMO IER Страницы: 40

Бренд: Ecco Страницы: 2

Бренд: Oakley Sound Страницы: 15

Бренд: Oasis Страницы: 18

Бренд: Jasco Страницы: 2

Бренд: Omnitronic Страницы: 24

Бренд: NAPCO Страницы: 80

Бренд: Community Страницы: 60

Бренд: Response Alarms Страницы: 16

Picomig 305 D2 puls

Бренд: EWM Страницы: 84

Бренд: Air Liquide Страницы: 16

Бренд: Monacor Страницы: 2

Бренд: Jam Страницы: 9

Бренд: Jam Страницы: 3

Бренд: TAD Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды