JVC TM-A101G/E Скачать руководство пользователя страница 8

Страница: 8 / 33

No. 51921

TM-A101G

REPLACEMENT OF MEMORY IC

1. MEMORY IC

This model uses memory IC. In the memory IC, memorized data

for correctly operating for the video-chroma, deflection and the

other control circuits.

When replacing memory IC, be sure to use the IC written with

the initial values of data.

2. PROCEDURE FOR REPLACING MEMORY IC

(1) Power off

Turn the power off and unplug the power plug from the AC

outlet.

(2) Replace IC

Be sure to use the memory IC written with the initial setting

data.

(3) Power on

Connect the power plug into the AC outlet and turn the

power on.

(4) Check and set SET-UP MENU items

1) Press the

MENU

key and the

CHROMA/PHASE

key

simultaneously.

2) The SET-UP MENU screen (Fig. 1) will be displayed.

3) Check the setting value of the each item of the SET-UP

MENU. If the value is different, select the item and set the

correct value.

4) Press the

MENU

key, and return to the normal screen.

(5) Check and set MENU items

Press the

MENU

key and check the setting value of the each

item. If the value is different, select the item and set the

correct value.

(6) Adjust the front control items

Adjust the CHROMA, PHASE, CONTRAST and BRIGHT.

Not all items can be adjusted as expected if the signal has

not been input correctly in the adjustments.

(7) Confirm the items of SERVICE MENU

Confirm the each item of the SERVICE MENU. Refer to the

corresponding page to operate the SERVICE MENU.

SIGNAL BLOCK

WHITE BALANCE BLOCK

DEFLECTION BLOCK

CONTROL BLOCK

< BLOCK SELECT >

SIG W/B

DEF

CNTL

EXIT

SERVICE MENU

<BLOCK SELECT> SCREEN

SET-UP MENU

< SET-UP MENU>

EXIT

H.POSITION

:00

WHITE BALANCE

CONTROL LOCK :OFF

STATUS DISPLAY :ON

INPUT REMOTE :OFF

ASPECT REMOTE :OFF

Fig.1

CURSOR

Display with the current adjusting item. Operate with the

CHROMA/PHASE

key and

CONTRAST/BRIGHT

key.

SETTING ITEM

The items of setting

SETTING VALUE

Adjust each item of SET-UP MENU with the

VOLUME/

SELECT

(

)key.

FUNCTION DISPLAY

When you move the cursor to select the item, the function

display changes the illustration.

OPERATION KEY ARRANGEMENT

In the SERVICE MENU, the original key operation by the

front panel replaced with the displayed function.

Содержание TM-A101G/E


































Результаты поиска

Содержание TM-A101G/E

Отзывы:

Похожие инструкции для TM-A101G/E

Бренды по названию

Популярные бренды

JVC TM-A101G/E, Руководство по обслуживанию

Результаты поиска

Содержание TM-A101G/E

Отзывы:

Похожие инструкции для TM-A101G/E

Бренды по названию

Популярные бренды