JVC TM-A101G/E Скачать руководство пользователя страница 30

Страница: 30 / 33

No. 51921

TM-A101G

PURITY / CONVERGENCE ADJUSTMENT

PURITY ADJUSTMENT

1. Demagnetize CRT with the demagnetizer.

2. Loosen the retainer screw of the deflection yoke.

3. Remove the wedges.

4. Input a green raster signal from the signal generator, and turn

the screen to green raster.

5. Move the deflection yoke backward.

6. Bring the long lug of the purity magnets on the short lug and

position them horizontally. (Fig.2)

7. Adjust the gap between two lugs so that the GREEN RASTER

will come into the center of the screen. (Fig.3)

8. Move the deflection yoke forward, and fix the position of the

deflection yoke so that the whole screen will become green.

9. Insert the wedge to the top side of the deflection yoke so that it

will not move.

10. Input a crosshatch signal.

11. Verify that the screen is horizontal.

12. Input red and blue raster signals, and make sure that purity is

properly adjusted.

CRT

WEDGE

DEFLECTION

YOKE

P / C

MAGNETS

4 6

PURITY MAGNETS

Long lug

Short lug

Bring the long lug over the short lug
and position them horizontally.

(FRONT VIEW )

GREEN RASTER

CENTER

P : PURITY MAGNET
4 : 4 POLES (convergence magnets)
6 : 6 POLES (convergence magnets)

P/C MAGNETS

Fig.1

Fig.3

Fig.2

Содержание TM-A101G/E


































Результаты поиска

Содержание TM-A101G/E

Отзывы:

Похожие инструкции для TM-A101G/E

Бренды по названию

Популярные бренды

JVC TM-A101G/E, Руководство по обслуживанию

Результаты поиска

Содержание TM-A101G/E

Отзывы:

Похожие инструкции для TM-A101G/E

Бренды по названию

Популярные бренды