6
INTRODUCTION
Active movement camera with integrated
moving mechanism and camera.
B a c k l i g h t c o m p e n s a t i o n f u n c t i o n
provided. Enables improvement of video
image shot under backlit conditions.
Electronic shutter with a selectable
shutter speed of 1/100 sec (U), 1/60 sec
( E ) r e d u c e s f l i c k e r i n g c a u s e d b y
fluorescent lighting in areas where the
commercial power supply frequency is 50
Hz (U), 60 Hz (E).
Employment of TTL automatic tracking
white balance allows use under various
light source conditions.
Panic alarm input terminal provided.
Electronic zoom function.
Control possible via external control
signal conforming to the EIA/TIA RS-
422A or RS-485 standard. The unit can
be controlled using the optional JVC
Remote Control Unit RM-P2580.
The following functions are available
when used in combination with the JVC
Remote Control Unit RM-P2580.
• Many kinds of function can be set using
menus.
• Camera text, position text setting.
• Auto panning function
• Auto patrol function
This function outputs the video image
at specified pre-set positions in the set
order.
Features
Safety Precautions
Installation of this unit requires expertise.
Please contact your JVC dealer for details.
Be sure to tighten the screws and nuts used
for installation securely. Insufficient tightening
could cause the unit to fall from its mount.
7
Operating Precautions
●
To save energy, be sure to turn off the
system when not in use.
●
This camera has been designed for indoor
use. It cannot be used outdoors.
●
T h i s c a m e r a h a s b e e n d e s i g n e d
exclusively to be hung from the ceiling. It
may malfunction if it is placed standing
on a surface or if it is installed in a tilted
position.
●
Do not install or use the camera in the
following places.
• In a place exposed to rain or water.
• In a place with vapor or oil soot, for
example in a kitchen.
• Where the temperature is outside the
allowed operating temperature range
(
−
10°C to 50°C).
• Near a source of radiation, X-rays,
strong radio waves or magnetism.
• In a place subjected to vibrations.
• In a place with excessive dirt.
●
The camera incorporates an AGC circuit.
When it is used under low light conditions,
the camera sensitivity is automatically
boosted and the picture may look grainy.
This is not a malfunction.
●
Use the ATW (auto-tracking white
balance) mode when the camera is used
under fluorescent lighting. If set to
MANUAL, the correct white balance may
not be accomplished.
●
When this camera is used in the ATW
(auto-tracking white balance) mode, the
recorded colors may be slightly different
f r o m t h e a c t u a l c o l o r s d u e t o t h e
operational principles of the auto-tracking
white balance circuit. This is not a
malfunction.
●
If a high-intensity object (such as a lamp)
is shot, the image on the screen may have
vertical lines (smear) or blur (blooming)
at its periphery. This is a characteristic of
the CCD; and it is not a defect.
●
The camera’s electronic shutter is set to
1/60 s (U), 1/50 s (E) when shipped from
the factory.
W h e n t h e c a m e ra i s u s e d u n d e r
fluorescent lighting in an area with a local
power frequency of 50 Hz (U), 60 Hz (E),
please set the shutter to 1/100 s (U), 1/
60 s (E) on remote control unit. (Sensitivity
will decrease slightly at the 1/100 s (U),
1/60 s (E) setting.)
●
When dirt adheres to the dome cover, the
image will be difficult to see. Be sure to
clean the lens and the dome cover
periodically. Use a soft cloth for cleaning.
Do not use thinner, benzene, etc. If very
soiled, soak the cloth in a neutral
detergent diluted with water and wipe
clean. Then wipe with a dry cloth.
Precautions for use with the RM-P2580
●
Focus (including AF) cannot be used.
●
Do not select more than maximum 16
preset positions.
●
ALARM TEXT EDIT 1 to EDIT 10
cannot be used.