JVC TH-M65 Скачать руководство пользователя страница 9

Страница: 9 / 42

(No.MB112)1-9

3.1.3 Removing the DVD changer mechanism assembly

(See Fig.7)

• Prior to performing the following procedures, remove the metal

cover and front panel assembly.

(1) From the top side of the main body, disconnect the card

wires from the connectors (

CN405

CN415

) on the main

board.

(2) Remove the four screws

attaching the DVD changer

mechanism assembly to the bottom chassis.

(3) Take out the DVD changer mechanism assembly in an

upward direction.

Note:

When attaching the screw

, fit the hole of the DVD changer

mechanism assembly to the bosses

on the bottom chassis.

Fig.7

3.1.4 Removing the rear panel

(See Fig.8)

• Prior to performing the following procedure, remove the metal

cover.

(1) From the back side of the main body, remove the screw

ten screws

and three screws

attaching the rear panel.

Fig.8

Main board

Boss

CN405

CN415

Bottom chassis

DVD changer mechanism

assembly

Card wires

F G

Rear panel

Содержание TH-M65











































Результаты поиска

Содержание TH-M65

Отзывы:

Похожие инструкции для TH-M65

Бренды по названию

Популярные бренды

JVC TH-M65, Руководство по обслуживанию

Результаты поиска

Содержание TH-M65

Отзывы:

Похожие инструкции для TH-M65

Бренды по названию

Популярные бренды