JVC TH-M65 Скачать руководство пользователя страница 11

Страница: 11 / 42

(No.MB112)1-11

3.1.8 Removing the main board

(See Figs.11 to 13)

• Prior to performing the following procedures, remove the metal

cover.

(1) From the top side of the main body, disconnect the card

wires from the connectors (

CN405

CN407

CN410

CN411

CN413

CN415

) on the main board. (See Fig.11.)

[US/UW/UG version]

(2) From the top side of the main body, disconnect the card

wires from the connectors (

CN405

CN407

CN410

CN411

CN412

CN415

) on the main board. (See Fig.11.)

[UJ version]

(3) Disconnect the parallel wires from the connectors (

CN416

CN402

CN404

CN408

CN409

) on the main board. (See

Fig.11.)

(4) Remove the screw

attaching the audio & digital input

board. (See Fig.11.)

(5) From the back side of the main body, remove the five

screws

and three screws

attaching the rear panel. (See

Fig.12.)

(6) Take out the rear panel together the audio & digital input

board and tuner.

(7) From the top side of the main body, remove the screw

and two screws

attaching the main board to the bottom

chassis. (See Fig.13.)

Note:

When attaching the screw

, attach the earth wire of the front

panel assembly at the same time.

Fig.11

Fig.12

Fig.13

CN411

CN413

CN402

CN407

CN409

CN408

CN410

CN403

CN404

Tuner

Audio & Digital input board

Main board

CN416

CN405

CN415

Parallel wires

Card wire

Card wires

Parallel wire

CN412

Card
wires

Rear panel

Main board

Earth wire

Front panel assembly

Bottom chassis

Содержание TH-M65











































Результаты поиска

Содержание TH-M65

Отзывы:

Похожие инструкции для TH-M65

Бренды по названию

Популярные бренды

JVC TH-M65, Руководство по обслуживанию

Результаты поиска

Содержание TH-M65

Отзывы:

Похожие инструкции для TH-M65

Бренды по названию

Популярные бренды