Masterpage:Right+
EN
49
Filename [SR-MV50U_08VCR Operation.fm]
Page 49
November 22, 2004 1:03 pm
OPERATIONS ON VCR DECK
You can program this unit to timer record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to timer
record the program.
1
Load a cassette with the record safety tab intact. If not, set
“REC SAFETY” to “OFF” (
墌
pg. 73).
2
Press
VCR/DVD
repeatedly so that the VCR lamp lights up on
the unit.
3
Press
PROG/CHECK
to access the
Program Check screen.
4
Press
rt
to select the blank
number, then press
ENTER
. The
program screen appears.
5
Press
w e
to select “START”, then
press
rt
to set the desired start time.
●
Each press of
rt
increases/decreases
the start time in 1 minute interval.
●
To increase/decrease the start time in
30-minutes interval, press and hold
rt
.
6
Press
w e
to select “STOP”, then press
rt
to set the desired
stop time.
●
Each press of
rt
increases/decreases the stop time in 1 minute
interval.
●
To increase/decrease the stop time in 30 minutes interval, press and
hold
rt
.
7
Press
w e
to select “DATE”, then press
rt
to set the desired
date.
●
The current date appears on the TV screen. The date you enter
appears in its place.
8
Press
w e
to select “CH”, then press
rt
to select the desired
channel.
9
Press
REC MODE
to select the desired recording mode. Or
press
w e
to select “SP/EP”, then press
rt
to select the desired
recording mode.
10
Press
ENTER
to access the Program Check screen.
11
Press
PROG/CHECK
to complete timer programming.
“PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen appears. If “PROGRAM NOT
COMPLETED PROGRAM OVERLAP” appears on the TV screen,
see page 50.
●
To program another timer, repeat steps
3
–
11
.
12
Press
VCR TIMER
(
#
) to engage the unit’s timer mode. The
VCR timer indicator lights up on the front display panel and the
DVD deck is automatically selected. When the DVD deck is in
timer standby mode, the unit is automatically turned off.
●
To disengage the timer mode, press
VCR TIMER
(
#
) again.
NOTES:
●
To Timer Record Weekly Or Daily Serials:
— anytime during steps
7
through
9
, press
number key “9”
for
weekly serials or
number key “8”
for daily serials (Monday – Friday).
Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
●
You can program this unit to timer record as many as 8 programs. If
you try to program the unit to record a ninth, “PROGRAM FULL”
appears on the TV screen. To record the extra program, you must
first cancel any unnecessary programs. (
墌
pg. 50)
●
In case of a power failure after programming, the unit’s memory
backup keeps your selections for approximately 5 seconds.
●
Programs that start after midnight must have the next day’s date.
●
To record the programs received by cable box or DBS receiver,
record on the DVD discs. For details, refer to “Manual Timer
Programming” (
墌
pg. 39).
Manual Timer Programming
●
Make sure that the unit’s built-in clock is set properly.
●
Turn on the unit.
●
Turn on the TV and select the video channel (or AV mode).
●
Slide the
TV/CABLE/DBS/DVD
switch to
DVD
.
1
4
7
2
5
8
0
3
6
9
PROG/CHECK
ENTER
VCR TIMER (
#
)
rtw
e
VCR/DVD
0 – 9
REC MODE
(PROG/CHECK) TO NEXT
PR START
STOP
CH
DATE
1
8:00P
10:00
12
12/24
2
10:00A
10:45 40
12/25
3
11:30P
1:00 125
12/25
4
5
6
7
8
PROGRAM 4
START
STOP
– –:– –AM
– –:– –AM
DATE
CH SP/EP
– –/– –/– –
– – –
SP
PRESS (
RTYU
, 8=DAILY
9=WEEKLY), THEN (ENTER)
(PROG/CHECK) TO END
SR-MV50US.book Page 49 Monday, November 22, 2004 1:03 PM
