Masterpage:Right+
EN
39
Filename [SR-MV50U_07DVD Operation2.fm]
Page 39
November 22, 2004 1:03 pm
OPERATIONS ON DVD DECK
You can program this unit to timer record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to timer
record the program.
1
Load a recordable disc.
2
Press
VCR/DVD
repeatedly so that the DVD lamp lights up on
the unit.
3
Press
PROG/CHECK
to
access the Program Check
screen.
●
When “PROGRAM FULL DELETE
UNWANTED TIMER PROGRAM”
appears on the TV screen, you
need to cancel some of the
reserved programs. (
墌
pg. 42)
4
Press
rt
to select “NEW
TIMER PROGRAM”, then press
ENTER
. The program screen
appears.
5
Press
rt
to set the desired
date.
●
The current date appears on the
TV screen. The date you enter
appears in its place.
6
Press
w e
to select “START”, then press
rt
to set the desired
start time.
●
Each press of
rt
increases/decreases the start time in 1-minute
interval.
●
To increase/decrease the start time in 30-minutes interval, press and
hold
rt
.
7
Press
w e
to select “STOP”, then press
rt
to set the desired
stop time.
●
Each press of
rt
increases/decreases the stop time in 1-minute
interval.
●
To increase/decrease the stop time in 30-minutes interval, press and
hold
rt
.
8
Press
w e
to select “CH”, then press
rt
to select the desired
channel.
●
If you are using a DBS receiver, see “ATTENTION FOR DBS
RECEIVER USERS” in the right column.
9
Set the other recording options as required.
●
Refer to step
6
in “VCR Plus+
®
Timer Programming” (
墌
pg. 38).
10
Press
ENTER
to access the Program Confirmation screen.
11
Press
ENTER
to complete timer programming.
●
To program another timer, repeat steps
3
–
11
.
12
Press
DVD TIMER
(
#
) to engage the unit’s timer mode. The
DVD timer indicator lights up on the front display panel and the
VCR deck is automatically selected. When the VCR deck is in
timer standby mode, the unit is automatically turned off.
●
To disengage the timer mode, press
DVD TIMER
(
#
) again.
NOTES:
●
When two successive programs are recorded on a DVD-RW disc
with Manual Timer programming function, the beginning of the
second one may be left off the recording.
●
If the copy limited program is received during timer recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programmed.
Manual Timer Programming
●
Make sure that the unit’s built-in clock is set properly.
●
Turn on the unit.
●
Turn on the TV and select the video channel (or AV mode).
●
Slide the
TV/CABLE/DBS/DVD
switch to
DVD
.
1
4
7
2
5
8
0
3
6
9
PROG/CHECK
7
ENTER
DVD TIMER (
#
)
rtw
e
VCR/DVD
Cable Box and DBS Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A
Perform “Manual Timer Programming” (
墌
pg. 39).
B
Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C
Leave the cable box or DBS receiver’s power on.
ATTENTION FOR DBS RECEIVER USERS
If you are using a DBS receiver, the band indication (TV, CATV
or DBS) appears on the left of the channel number indication.
No indication
: To timer record a regular TV broadcast received
on the unit.
CATV
: To timer record a cable TV broadcast received on the unit,
or through a cable box.
DBS
: To timer record a satellite broadcast received through a
DBS receiver.
NOTE:
If the channel number entered requires that the band be set,
“7=DBS” is displayed on the screen.
If this happens, press the
number key “7”
to select “DBS”.
SR-MV50US.book Page 39 Monday, November 22, 2004 1:03 PM