JVC GD-V4210PCE, Руководство по обслуживанию

Страница: 67 / 114

1-20
37
ENGLISH
Self-diagnostic Indication
The screen monitor may automatically turn off and self-diagnostic lamps next to the power lamp may light or flash.
When something abnormal occurs with the Monitor, this function informs you of the condition of the Monitor with self-
diagnostic lamps, allowing for smooth service work.
If the self-diagnostic lamps glow or flash in red, use the following procedure before consulting the dealer where you purchased
the Monitor.
1
Check which lamps are lighting or flashing.
On the Self-diagnostic Report Sheet (below), check the box next to “Lights” or “Flashes” of the corresponding lamp or
lamps.
• Depending on a particular case, only one lamp may light or flash, or all three lamps may do so.
2
Turn off the MAIN POWER switch on the back of the Monitor.
3
Unplug the power cord.
4
Call your dealer and tell which lamps are lighting or flashing. (Copy and fax the Self-
diagnostic Report Sheet below.)
Note:
• If you turn on the Monitor soon after turning it off (or after recovering from a brief power interruption), the self-diagnostic
lamps may light (or flash), and no image may appear on the screen. In this case, turn off the Monitor again, wait for about 10
seconds, then turn it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual.
The self-diagnostic lamps light or flash as listed on the following
table. Please give me immediate advice or service if necessary.
MENU INPUT POWER
Self-diagnostic lamps (1 to 3)
Remote sensor
Power lamp
1
2
3
Self-diagnostic lamps
Upper 1
2 Middle
3
NO. Lamp position Conditions
Lower
&
Flashes
&
Flashes
&
Flashes
&
Lights
&
Lights
&
Lights
Your Name:
Telephone No.:
Address:
Store name where you purchased the Monitor
To
Model Name:
Plasma Display Monitor
GD-V4210PZW/GD-V4210PZW-G
GD-V4210PCE/GD-V4210PCE-G
GD-V4211PCE
Self-diagnostic Report Sheet
36
• Is the power cord disconnected?
•Is the MAIN POWER switch turned on?
•Is the correct input selected?
•Are the devices connected correctly?
•Are signals being supplied from the
connected devices?
•Is RGB INPUT set correctly if using the
RGB terminals?
•Are input signals (scanning frequency,
etc.) appropriate?
•Is brightness adjusted correctly?
•Is volume set at minimum?
•Are the diagnostic lamps turned on?
•Is the signal RGB input?
•Is brightness adjusted correctly?
•Is picture quality (colour density, etc.)
adjusted correctly?
•Is the correct broadcast system (colour
system) selected?
•Are signals (scanning frequency, etc.) to
connected devices appropriate?
•Is the size or position of the screen
adjusted properly?
•Are the batteries correctly set?
•Are the batteries exhausted?
•Is there any object blocking the path
between the remote control and remote
sensor?
•Is the Monitor too far away from you?
•Is the Monitor connected serially to
another Monitor (Serial Connection)?
•Is the Control Lock function in use?
Troubleshooting
Solutions to common problems related to the Monitor are described here. If none of the solutions presented here solves the
problem, unplug the Monitor and consult an authorized dealer or service center.
Symptom Probable cause Corrective action Page
•Insert the power cord (plug) firmly.
•Turn on the MAIN POWER switch.
•Select the correct input by pressing
VIDEO A, VIDEO B, COMPO. and
RGB on the remote control (or INPUT
on the Monitor).
•Connect the devices correctly.
•Set the devices correctly.
•Set it correctly.
•Check if the signal is appropriate
(scanning frequency, etc.), and input
the appropriate signal.
•Adjust brightness on the menu.
•Adjust volume.
•Refer to “Self-diagnostic indication,”
and take an appropriate action.
•Adjust CLOCK PHASE using the
menu.
•Adjust BRIGHT (brightness) using the
menu.
•Adjust PICTURE using the menu.
•Set SIGNAL MODE (colour system) to
“AUTO.”
•Check if the signal is appropriate
(scanning frequency, etc.), and input
the appropriate signal.
•Adjust H.SIZE, V.SIZE, H.POSITION
or V.POSITION using the menu.
•Insert batteries correctly, observing the
polarities (
ª
and
·
).
•Replace with new batteries.
•Remove any blocking object.
•Move toward the Monitor, then operate
the remote control.
•Only Master Monitor can be controlled
by the remote control when connected
serially.
•Set the Control Lock function to “OFF”
using the menu.
12
14
14
12, 13
—
23
11
16
14
37
17
16
16
22
11
17
9
9
—
—
31
26
Power is not supplied.
Video image does not
appear, or audio
sound does not occur.
The picture becomes
blurred
.
Colour is abnormally
dark or bright.
Colour is poor or
unstable.
The picture is cut or
shifted toward one
side.
The remote control
does not work.
The buttons on the
Monitor do not work.