JVC DX97US - GRDX97 MiniDV Digital Camcorder, Инструкция по эксплуатации

Страница: 40 / 52

EDITING
40
EN
MasterPage: Left
The audio track can be customized only when recorded
in the 12-BIT and SP modes. (
墌
pg. 28)
●
Use the provided remote control or an optional remote
control kit RM-V717KITU.
1
Play back the tape to locate the point where editing
will start, then press PAUSE (
9
).
2
While holding A. DUB (
D
) on the remote control,
press PAUSE (
9
). The “
9
D
” and “MIC” indicators
appear.
3
Press PLAY (
U
), then begin “narrating”. Speak into
the microphone.
●
To pause dubbing, press PAUSE (
9
).
4
To end Audio Dubbing, press PAUSE (
9
), then STOP
(
8
).
To hear the dubbed sound during playback
Set “NARRATION” to “ON” or “MIX”. (
墌
pg. 27, 30)
NOTES:
●
Sound is not heard from the speaker during Audio Dubbing.
●
When editing onto a tape that was recorded at 12-BIT, the
old and new soundtracks are recorded separately.
●
If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
●
If feedback or howling occurs during TV playback, move the
camcorder’s microphone away from the TV, or turn down
the TV’s volume.
●
If you change from 12-BIT to 16-BIT in mid-recording and
then use the tape for Audio Dubbing, it is not effective from
the point where 16-BIT recording began.
●
During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-BIT audio
or a blank portion, Audio Dubbing stops.
●
Audio dubbing is also possible using an optional
microphone connected to the MIC connector.
●
While an optional microphone is connected, the built-in
microphone is disabled.
●
To perform Audio Dubbing with a video unit connected to
the camcorder’s AV connector, first set “S/AV INPUT” to “A/
V.IN” or “S.IN” in VIDEO Menu. (
墌
pg. 27, 30)
The “AUX” indication appears instead of “MIC”.
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
●
Use the provided remote control or an optional remote
control kit RM-V717KITU.
NOTES:
●
Before performing the following steps, make sure that
“TIME CODE” is set to “ON”. (
墌
pg. 27, 31)
●
Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
1
Play back the tape, locate the Edit-Out point and
press PAUSE (
9
). Confirm the time code at this point.
(
墌
pg. 17)
2
Press REW (
3
) until the Edit-In point is located,
then press PAUSE (
9
).
3
Press and hold INSERT (
I
) on the remote control,
then press PAUSE (
9
). The “
9
I
” indicator and the Time
Code (min.:sec.) appear and the camcorder enters
Insert-Pause mode.
4
Press START/STOP to begin editing.
●
Confirm the insert at the time code you checked in step
1
.
●
To pause editing, press START/STOP . Press it again to
resume editing.
5
To end Insert Editing, press START/STOP , then
STOP (
8
).
NOTES:
●
Program AE with special effects (
墌
pg. 35) can be used to
spice up the scenes being edited during Insert Editing.
●
During Insert Editing, the date and time information
changes.
●
If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure you
only edit recorded areas.
●
During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops. (
墌
pg. 47)
Audio Dubbing
PAUSE
PLAY
A.DUB
STOP
REW
INSERT
START/
STOP
Microphone Connector
Speaker
Stereo Microphone
Insert Editing
GR-DX97US.book Page 40 Monday, February 9, 2004 2:28 PM