JVC D-ILA LD-HD2KBE, Инструкция по эксплуатации

Страница: 26 / 72

Adjustments and Settings Using Menus (continued)
26
A
Input Menu
● A
Input
B
setting of the
A
Input
B
menu can also be set using
the input selection buttons on the remote control.
(
A
Page 12)
Formats
.................................................................................................
Input
Sets signals to input to this unit.
.................................................................................................
Aspect
Use these to set the aspect ratio of video signal output
from this unit.
●
Sets the screen’s aspect ratio in the Setup menu. When
the
A
Anamorphic
B
aspect ratio is selected while the screen
shape setting is set to
A
4:3
B
and
A
WIDE 4:3
B
, signals at a
scan rate of 480p, 540p and 600p and those that have
undergone frame doubling cannot be used.
●
When using a 4:3 source on a Wide Angle screen, a black
bar will appear on the left and right sides of the image. The
sidebars can be changed to gray color by adjusting
A
Border Lvl
B
in the
A
Display
B
menu. If filling the entire
screen is desired, set
A
Aspect
B
of the
A
Input
B
menu to
A
Letterbox
B
. The image will fill the screen but part of the
image at the top and bottom will not be displayed
(overscanned).
●
When watching 2.35:1 aspect ratio movies on a 16:9
(1:77) screen, it is normal to see black bars at the top and
bottom of the image.
Profile Button
.................................................................................................
Recall
Invokes the stored profile.
.................................................................................................
Store
Stores up to 8 profiles each for NTSC and PAL.
o
Storing a profile
1. Press the [MENU] button on the remote control to
display the OSD menu
2. Set (Adjust) accordingly
3. Press the [
J
/
K
] buttons to select
A
Store
B
4. Press the [
H
/
I
] buttons to select a profile number
(1 to 8) to store the settings to
5. Press the [STORE] button to save the profile
o
Invoking a profile
1. Press the [MENU] button on the remote control to
display the OSD menu
2. Press the [
J
/
K
] buttons to select
A
Recall
B
3. Press the [
H
/
I
] buttons to select a profile number
(1 to 8) to invoke
4. Press the [STORE] button to invoke the profile
OSD Menu Configuration
Setting Values: DVI, Video, S-Video, RGB, YCrCb
Default Value: DVI
Setting Values: Anamorphic, Letterbox, 4
⳯
3
Default Value: Anamorphic
CAUTION:
Do not project images except for those at 16:9 (e.g. 4:3,
etc.) on display devices with a screen size of 16:9 for long
periods of time. This can cause permanent image burn-in.
Image burn-in is not covered by warranty.
Input DVI
Aspect
Profile
Recall
Store
Formats
F 1 2 3 4
Input
Picture
Anamorphic
Patterns Display
1 2 3 4
Setting Values: F (Factory), 1, 2, 3, 4, 5, 6, 7, 8
Setting Values: 1, 2, 3, 4, 5, 6, 7, 8
NOTES:
●
When settings are altered after invoking a profile, these
will automatically overwrite the old settings.
●
It is also possible to invoke a profile from the computer
via RS-232C.
NOTE:
The menus below will not function if
A
SET: 1080i TO
1080p
B
is set to
A
HIGH BANDWIDTH MODE
B
.
●
Aspect
●
Tint
●
Detail
●
Adv Color (Advanced Color System)
●
Display
LD-HD2KU_E.book Page 26 Thursday, November 17, 2005 4:27 PM