JVC CA-MXK50R страница 24 Скачать руководство пользователя | Manualshive

Страница: 24 / 70

background image

MX-K50R

1-24

Turn off the power switch and,disconnect the
power cord from the ac outlet.

Replace the pickup with a normal one.(Refer
to "Pickup Removal" on the previous page)

Plug the power cord in,and turn the power on.
At this time,check that the laser emits for
about 3seconds and the objective lens moves
up and down.
Note: Do not observe the laser beam directly.

Play a disc.

Check the eye-pattern at TP1.

Finish.

Maintenance of laser pickup

Is the level of

RF OUT under

1.1V 0.2Vp-p?

Replace it.

NO

YES

O.K

(3) Semi-fixed resistor on the APC PC board

Replacement of laser pickup

(2) Life of the laser diode
When the life of the laser diode has expired,
the following symptoms will appear.

1. The level of RF output (EFM output :
amplitude of eye pattern) will below.

(1) Cleaning the pick up lens
Before you replace the pick up, please try to
clean the lens with a alcohol soaked cotton
swab.

The semi-fixed resistor on the APC printed circuit board which is attached to the pickup is used to adjust the
laser power. Since this adjustment should be performed to match the characteristics of the whole optical block,
do not touch the semi-fixed resistor.
If the laser power is lower than the specified value, the laser diode is almost worn out, and the laser pickup
should be replaced.
If the semi-fixed resistor is adjusted while the pickup is functioning normally, the laser pickup may be damaged
due to excessive current.

«
...
22
23
24
25
26
...
»

Содержание CA-MXK50R







































































Отзывы:

Нет отзывов

Похожие инструкции для CA-MXK50R

Бренд: Tannoy Страницы: 8

Бренд: JBL Страницы: 10

Бренд: Wavemaster Страницы: 4

Бренд: La Crosse Technology Страницы: 2

Бренд: TCL Страницы: 16

HQ Power VDSABS15A

Бренд: Velleman Страницы: 13

Бренд: Yardgard Страницы: 8

Бренд: Spon Страницы: 9

Бренд: Zenitel Страницы: 4

Бренд: TOKK Страницы: 4

Mobile Multimedia AM/FM/DVD Receiver VM9311

Бренд: Jensen Страницы: 90

Бренд: Qvis Страницы: 32

Бренд: CABASSE Страницы: 16

Бренд: Mackie Страницы: 16

Бренд: HÜRNER Страницы: 33

Бренд: Harman Kardon Страницы: 38

Бренд: Abra Страницы: 4

Бренд: Nalnor Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды